Assessments - 3, GPA: 5 ( )

Fabricante : Star Trac Arquivo Tamanho: 2.62 mb Arquivo Nome : Língua de Ensino:

Once the center console has been mounted into the display connect the head phone jack to the appropriate jack as noted. 620-7991 Rev 002 STEP 11. While holding the new center console near the opening of the display, connect the following cables to there appropriate connector. (There is no particular order): 1 • Plug in the (2) DC power cables to the DC connectors, (they are the same so it does not matter which goes to which). 2 • Plug in the PVS remote cable to the PVS remote connector. • Plug in the A/V cable to the audio (6-pin) and the video (2-pin) connector, respectively, to the A/V connectors on the center console board. 4 5 • Take the keypad tail, and the center console ground and feed them through the cable window. STEP 12. Close the center console. Using a #2 Phillips screwdriver, take the screws retained from earlier and screw in the (4) screws from below that hold in the center console. Tighten the screws snug. 620-7991 Rev 002 STEP 13. • Plug the center console’s ground cakey- In3 2 1 ble into the quick disconnect tab on the back display mount. • Connect the keypad tail to the pad connector on the display board. • Connect the interface cable to the terface connector J11 on the display board. STEP 14. Go to the base of the treadmill neck. Using a #2 Phillips screwdriver, remove the (2) screws that hold in the RF cable Mounting Bracket. Retain the screws for later use. STEP 15. Remove the nut and washer from the F-Type connector on the end of the coax cable you fed down the treadmill neck, then put connector through the mounting bracket. Replace the nut and washer, and tighten the nut snugly. Next replace mounting bracket into the neck, using the screws retained from previous step. Tighten with a #2 Phillips screwdriver. STEP 16. Replace the bottom back plastic cover. Using a #2 Phillips screwdriver insert the (6) screws, retained from earlier step, into the plastic and tighten snug. Caution: Do not over tighten screws. 620-7991 Rev 002 STEP 17. Replace the top back plastic cover. Using a #2 Phillips screwdriver insert the (8) screws, retained from earlier step, into the plastic. Do Not tighten screws at this time. STEP 18. Check the cap with the neck and grommet. Make sure the cap is flush with the top back plastic. Adjust if necessary. Use the screwdriver to tighten the screws snug from the previous step. Caution: Do not over tighten screws. This completes the installation of the Personal Viewing Screen on the E-TR / E-TRx treadmill. Now it is time to set it up. Turn to the appropriate section for your Personal Viewing Screen. 620-7991 Rev 002 SETTING UP YOUR PERSONAL VIEWING SCREEN (NTSC / ATSC) SETTING UP YOUR PERSONAL VIEWING SCREEN (NTSC / ATSC) Basic Operations Turning On / Off the Power Turning On Press the button on the control module, the unit will be turned on and you will be ready to use its features. Turning Off With the power on, press the button on the control module to turn off the unit. Note: • When selecting AV mode, the button can not work. If you want to turn off the unit, please select TV mode first. • In TV mode, when there is no signal input for 30 seconds, the unit will turn off the back light automatically. Once you press any button (except button) on the control module or the unit receives a signal input, the unit will display normally. • In AV mode, when there is no signal input for 3-5 seconds, the unit will turn off the back light automatically. When you press VOL+/-button or the unit receives a signal input, the unit will display normally. Selecting the Input Signal Source Press the INPUT button repeatedly to select your desired input source. Options include: • TV -Watch TV. • iPod -Listen to your iPod or watch a movie or other video from your iPod on the PVS screen. • USB -Listen to music from your USB device. Channel Selection You can use the following ways to change channels: • Press CH+ or CH-to go to the next or previous channel. The skipped channels can't be selected. • Press the number buttons to directly select any channel you want. • To go to the previous channel viewed, press the button. 620-7991 Rev 002 Adjusting Picture Menu Options Adjusting the Picture 1. Press VOL+, CH+ and number button [3] at the same time to display the main menu. 2. Press VOL+/-to select Picture menu, press CH-to access the menu. 3. Within the menu, press CH+/-, VOL-to navigate through the options or adjust an option. If the selected item has submenu, press VOL+ to access. 4. Press VOL+, CH+ and number button [3] at the same time to return to previous menu. Option Description Picture Mode Select a desired picture mode. You can select from Sport, Custom, Vivid, Standard, Energy Savings and Theater. Sport: Select for a dynamic picture. Custom: Select for a customized picture. Vivid: Select for a bright and vivid picture. Standard: Select for a standard picture. Energy Savings: Select for energy savings, the backlight brightness will be decreased. Theater: Select for a finely detailed ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :