Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• If no help – replace moving arm assembly. Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 11 Symptom Probable Cause Corrective Action Recommended Tools RESISTANCE MALFUNCTION Console Set • Remove console bolts to access 7-pin connector. Do not disconnect console Note: 600EA Lower Board / Brake Cable Brake Coil Console Cable set. Set meter for DC Volts. Measure between pin 1(red) and pin 5(blue) at 7- pin connector. • Enter DA (resistance) test mode. Page SG-1. • Press + key to force .9 VDC out of panel. • Press + to check voltage at all levels. Is voltage displayed on meter approximately the same as voltage displayed in heart rate window? No- replace console set. Yes, continue on. -------- • Remove main body cover & locate the cable connecting the brake and the lower control board. Set meter to DC volts. • Check DC voltage between pins 2 and 4 of the power supply • Is voltage is same as shown in heart rate window? • If NO – go to console cable. • Check voltage at the 2-pin connector at the brake. Press + to increase resistance and voltage. • Does the voltage start at 3.7 and increase to 30 VDC? If no- check continuity of cable. If cable is broken replace it, if cable is good – replace the lower board. -------- • Set meter to resistance and check the coil. Coil resistance should be 15 ohms, + or – 2 Ohms. If not then replace the coil. -------- • Set meter to resistance; perform continuity check on wire harness. • Check for cross continuity. • Broken wires? Replace cable. You must pedal at least 30 RPM when performing any voltage test. You may require the assistance of another person when performing voltage checks. Multi-meter Page 12 Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Symptom Probable Cause Corrective Action Recommended Tools NO DISPLAY Power Issues • Set meter to AC voltage and test wall Multi-meter 600EA Control Panel Power Supply outlet to 120 VAC. • Turn power switch on • Does power switch lamp come on? • Yes – go to control panel. • No- remove rear cover. • Check voltage input to switch, is it 120 VAC? If yes – replace switch. If no – continue on. • Check voltage at end of power cord. • No voltage? Replace cord. • Check fuse in power inlet. • Replace fuse or replace power inlet and wires. -------- • Check connection to the display. • Reseat connection. • Set meter to DC volts, unplug display and check voltage between pin 1and pin 2. • If 12VDC is present – replace control panel. -------- • Check voltage between pin 2and pin 3at the power supply. • If 12 VDC present – replace power supply. -------- Cables • Perform a continuity check on the cables leading to the control panel. • Replaced damaged cables. Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 Page 13 Symptom Probable Cause Corrective Action Recommended Tools NO SPEED READING 600EA Console Assembly • Remove monitor bolts. Move the swing arms until the magnet is in front of the sensor. • Set meter for DC volts. Check voltage between pin 3 and pin 1 at console assembly with cable connected. • Move swing arms. When magnet is over the pickup the voltage should be 0 VDC. When the magnet is not over the pickup, the voltage should be 5 VDC. • Does the voltage alternate between 0 VDC and 5 VDC? If yes – replace console assembly. -------- Multi-meter RPM Sensor • Turn power off, remove rear cover • Disconnect the sensor connector. Set meter for resistance. • Check resistance at the 2 pins of the connector. Slowly move the swing arms to rotate the wheel. • Does the meter show continuity when the magnet is over the pickup? If no – replace the sensor. -------- Defective ECB Control Board • Perform a continuity and contact check on the console wire. • Replace defective wire. Page 14 Support Services 800-883-8783 Mon-Fri 8:30am-5:00pm Central Time Zone Fax: 636-272-7148 WIRING DIAGRAMS ..TAE 600 Page 16 ..TAE 750 Page 17 ..TE 750 Page 18 Page 15 TRUE TAE 600 WIRING DIAGRAM Page 16 TRUE TAE 600 WIRING DIAGRAM Page 16 TRUE TAE 750 WIRING DIAGRAM TRUE TAE 750 WIRING DIAGRAM Page 17 TRUE TE 750 WIRING DIAGRAM TRUE TE 750 WIRING DIAGRAM Page 18 True Armed Elliptical 600B • Exploded Diagram Page 20 • Parts List Page 21 Page 19 TRUE TAE 600 PARTS DIAGRAM Page 20 TRUE TAE 600 PARTS DIAGRAM Page 20 TAE 600B REF # PART# DESCRIPTION QTY AC1 7TSZEP42CSM CONSOLE MAST ASSY 1 AE1 7TSZEP17PAM-6R1 RIGHT ARM ASSY 1 AE2 7TSZEP17PAM-6L1 LEFT ARM ASSY 1 AE3 7TSW0306011A MVG ARM PIVOT 2 AG1 7TSZEP25HDB-R HANDLEBAR ASSY RH 1 AG2 7TSZEP25HDB-L HANDLEBAR ASSY LH 1 AJ1 7TSZEP07FST FRNT STBL ASSY 1 AN1 7TS12325001 CONSOLE ASSY 1 AS1 7TMD0208010C BRAKE ECB SET 1 AT1 7TS08317001 CRANK ARM 2 B28 7TMB0301002 FOOT PAD WASHER 2 B29 7TMJ1390003E VERTCL SPT PLATE 1 B30 7TMJ1390004 UPPER SPT PLATE 1 B31 7TMB0302002 FOOT PAD 2 B51 7TME0102021 SCREW CVR SPT 6 C53 4 C54 4 C55 4 C56 7TMB0401050A STATIONARY BAR 2 E05 7TMB0609025 STABILIZER BAR 2 E07 7TSZEP25RAL AR...
Este manual também é adequado para os modelos :Formadores - 600EA (1.64 mb)
Formadores - 750EA (1.64 mb)