Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
You can take infrared relax sessions several times a day (e.g. 30 minutes in the morning and in the evening). Preparing for use You can easily move and store the appliance in transport position (Fig. ). ,1 Put the appliance on the floor as shown in the figure (Fig. 3). Make sure there is sufficient room on either side of the appliance to allow the legs to move outwards. Press the dual push button in the handgrip (1) and pull the stand slightly up ( ).Then release the push button (Fig. 4). On a smooth floor, the legs of the appliance automatically move outwards. If the floor is not smooth, e.g. a carpeted floor, you may have to put your foot on one of the legs to allow the other leg to move outwards. 3 Pull up the stand by the handgrip as far as it goes. (Fig. 5) The stand locks into position with a click. 4 Turn the lamp unit in the direction indicated in the figure. (Fig. 6) This requires some force at first. Push the lamp unit in the direction indicated until it locks into position with a click. You can only switch on the appliance for a tanning or relax session if the lamp unit is in the correct position. ,56 Push the legs of the appliance under the bed or sofa you intend to lie down on.The lamps for functions . and . are on the marked side of the appliance (HB947/HB945 only). (Fig. 7) Press the release buttons in the recesses of the control panel and push the control panel upwards along the stand. Let go of the release buttons when the lamp unit is at the required height. (Fig. 8) The distance between the UV filters and your body must be 70cm.The distance between the UV filters and the surface on which you lie , (e.g. a bed) must be 90cm. (Fig. 9) Pull out the measuring tape to determine whether the appliance is at the required height. (Fig. 10) , The measuring tape automatically rewinds when you operate the red tab. (Fig. 11) , using the appliance tanning or relaxing (HB933) 1 Fully unwind the mains cord. Put the plug in the wall socket. 3 Set the selector to the desired position (Fig. 1 ). Choose . if you want to tan your body. Choose if you prefer a relax session. 4 ‚Consult the chapters ‘Tanning and your health’ and ‘Relaxation and your health’ for the correct tanning or relax time. 5 6 ,, Put on the protective goggles provided. Only use these protective goggles when you tan with a Philips tanning appliance. Do not use them for other purposes. The protective goggles comply with protection class II according to directive 89/686/EEC. Lie down straight below the lamp unit of the appliance. 7 Set the timer to the appropriate time for the session. (Fig. 13) Note:It can take a few seconds for the lamps to go on.This is normal. The appliance beeps during the last minute of the session. , englIsH During this minute, you can reset the timer to tan the other side of your body. If you reset the timer during this minute, you avoid the , 3-minute waiting time which is necessary to let the tanning lamps cool down after they have switched off.This waiting time does not apply to the infrared lamps. tanning or relaxing (HB947 and HB945) 1 Fully unwind the mains cord. Put the plug in the wall socket. adjusting functions The function selection button shows the different functions. (Fig. 14) ,1 Press the function selection button to switch from function to function. (Fig. 15) The symbol that turns yellow shows the function you have selected. Choose: -symbol . if you want to tan your whole body -symbol . if you want to tan a specific part of your body -symbol if you want to relax ‚ -symbol . if you want to warm up a part of your body setting the time for a tanning or relax session. 1 Consult the chapters ‘Tanning and your health’ and ‘Relaxation and your health’ for the correct tanning or relax time. Turn the time-selection ring to set the time of the tanning or relax session (Fig. 16). Turn the ring clockwise to increase the time and turn it anticlockwise to decrease the time. 3 Put on the protective goggles provided. Only use these protective goggles when you tan with a Philips tanning appliance. Do not use them for other purposes. , The protective goggles comply with protection class II according to directive 89/686/EEC. ,45 Lie down straight below the lamp unit of the appliance. Press the START/STOP button to switch on the tanning lamps or the infrared lamps (Fig. 17). Note:It can take a few seconds for the lamps to go on.This is normal. 6 A blinking dot appears on the display next to the time. (Fig. 18) The countdown of the set tanning or relax time starts. last minute The appliance beeps during the last minute of the session. , During the last minute, you can repeat the set time. Press the repeat button ( a). (Fig. 19) , Note:The display shows the set time and starts to count down.The appliance stops beeping. During the last minute, you can set a new time.Turn the time-selection ring to the desired time (1) and then press the START/STOP , button ( ). (Fig. 0) Note:By setting a new time, you can avoid the 3-minute ...
Este manual também é adequado para os modelos :Formadores - HB945 (1.69 mb)
Formadores - HB947, HB945, HB933 (1.69 mb)