Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Note: For heavy use units it is advisable to use a wrench on the nuts and add additional torque to nut / bolt. STEP 5: Handles will install thru access holes in console upright. Remove both 5/16” Allen bolts in each handle with included wrench that is located in parts bag. Slide handle (flair to outside) thru access holes in console upright. Use caution to avoid data cables in left hand side console upright. You may observe data cable clearance from top of open console upright. Start both bolts into hand rail thru console upright. Repeat procedure for opposite hand rail. Tighten all bolts. Smooth 9.1 / 9.6 3 2/06/01 STEP 6: Place the treadmill in operating position. Make certain cables from upper computer do not come in contact with motor fan. Apply AC power. Start the unit and observe belt tracking. Unit must be reasonably level for proper tracking. Test treadmill basic operation. This includes noise, motor performance, etc. STEP 7: Install motor hood and secure with (2) black phillips head screws removed in step 4. Front of motor hood is not secured. The dealer must provide the following (minimum): n Follow the belt tracking instructions closely in order to ensure proper belt tension and path. n Walk on the belt at slow speeds under 2.5 mph for a few minutes in order to break in the belt/deck lubricant. n Make certain treadmill is electrically grounded. Contact Smooth Service 1-888-800-1167, ext. 103 Sales 1-800-TREADMILL Smooth 9.1 / 9.6 2/06/01 4 Important Operation Instructions Important Operation Instructions l NEVER operate this treadmill without reading and completely understanding the results of any operational change you request from the computer. l Understand that changes in speed and incline do not occur immediately. Set your desired speed on the computer console and release the adjustment key. The computer will obey the command gradually. l NEVER use your treadmill during an electrical storm. Surges may occur in your household power supply that could damage treadmill components. Removing safety cord will protect the unit. l Use caution while participating in other activities while walking on your treadmill; such as watching television, reading, etc. These distractions may cause you to lose balance or stray from walking in the center of the belt; which may result in serious injury. l NEVER mount or dismount the treadmill while the belt is moving. Smooth treadmills start with zero speed and it is unnecessary to straddle the belt during start up. Simply standing on the belt during slow acceleration is proper after you have learned to operate the unit. l Always hold on to a handrail or grab bar while making control changes (incline, speed, etc.). Do not use excessive pressure on console control overlays. They are precision set to function properly with little finger pressure. Pushing harder is not going to make the unit go faster or slower. If you feel the buttons are not functioning properly with normal pressure contact your Smooth dealer; adjustments can be made. All buttons should operate and control treadmill functions without excessive finger effort. Damage to overlay will result if excessive control pressure continues. Safety Tether Cord A safety tether cord is provided with this unit. It is a simple magnetic design that should be used at all times. It is for your safety should you fall or move too far back on the treadbelt. Pulling this safety tether cord will stop treadbelt movement. To Use: 1. Place magnet into position on the console control head. Your treadmill will not start and operate without this. Removing the magnet also secures the treadmill from unauthorized use. 2. Fasten the black plastic clip onto your clothing securely to assure good holding power. Note: The magnet has strong enough power to minimize accidental, unexpected stopping and the clip should be attached securely to make certain it does not come off. Be familiar with its function and limitations. Use the adjustment system to assure proper length of cord. The treadmill will stop, depending on speed, with a two to three step coast anytime the magnet is pulled off the console. Use the red STOP/PAUSE switch in normal operation. 5 Operation of Your New Treadmill Operation of Your New Treadmill DO NOT STAND ON THE WALKING BELT WHILE LEARNING TO OPERATE YOUR NEW TREADMILL!!! Basic Treadmill Operation: Step 1: Press and release DISPLAY ON/FAST key. Display will light. Step 2: For calorie computation if desired; (A) Calorie window will display LBS. (B) Use blue INCLINE keys to enter users weight. Note: If no weight is entered calories do not calculate and calorie window will not light. Step 3: For an elapsed (countdown) time press ENTER key. The Time/Pace window will indicate 20:00 (minutes). Adjust to desired time with blue INCLINE keys. Note: The above steps 2 & 3 are not required for operation of the treadmill. Step 4: Adjust to desired speed with FASTs/SLOWt keys. Step 5: Incline may be adjusted anytime with blue Up + / Do...