Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Handrail Console Fan Latch Knob Book Holder Key/Clip Reset/Off Circuit Breaker Walking Belt Foot Rail Power Cord Cushioned Walking Platform Rear Roller Adjustment Bolts Accessory Tray Pulse Sensor 5 ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrench , and rubber mallet and your own phillips screwdriver The number in parentheses below each drawing is the key number of the part, . For help identifying the assembly hard- ware, see the drawings below. , adjustable wrench from the PART LIST on pages 30 and 31. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre-assembled. If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly. Screw (60)–211” Tek Screw (82)–4Console Bolt (72)–43Extension Leg Bolt (87)–4Star Washer (67)–8Plastic Spacer(101)–4Extension LegNut (106)–42 1. Make sure that the power cord is unplugged. With the help of a second person, carefully tip the treadmill onto its side as shown. Partially fold the Frame (55) so the treadmill is more stable. Do not fully fold the treadmill until it is completely assembled. Orient an Extension Leg (97) so the Base Pad (81) is in the position shown, and insert the Extension Leg into the indicated bracket on the base of the Uprights (85). If necessary, use a rubber mallet to align the holes in the Extension Leg with the holes in the bracket. Attach the Extension Leg (97) with two Extension Leg Bolts (87), two Star Washers (67), and two Extension Leg Nuts (106) as shown. Firmly tighten the Bolts. With the help of a second person, carefully tip the treadmill onto its other side. Attach the other Extension Leg (97) as described above. 85 55 Bracket 97 1 106 87 67 81 6 2. Attach the four Base Pads (81) to the base of the Uprights (85) in the indicated locations with four 1” Tek Screws (82) and four Plastic Spacers (101). Note: One replacement Base Pad may be included. Use the Base Pad to replace any Base Pad that becomes worn. With the help of a second person, carefully tip the treadmill down so the four Base Pads (81) are resting on the floor and the Uprights (85) are in the vertical position. 3. Remove the band securing the Upright Wire Harness (73) to the right Upright (85). Have a second person hold the console assembly near the right Upright. Connect the Upright Wire Harness (73) to the wires extending from the console assembly. Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors into the right Upright (85). 4. With the help of a second person, set the console assembly on the Uprights (85). Make sure that no wires are pinched. Attach the console assembly with four Console Bolts (72) and four Star Washers (67) (only one side is shown). Start all four Console Bolts before tightening any of them. 85 82 81 101 101 101 101 82 55 81 72 67 85 67 Console Assembly 2 4 73 85 Console Assembly 73 3 7 5. Remove the knob from the pin. Make sure that the collar and the spring are on the pin. Press the Latch Insert (77) into the right side of the left Upright (85), and press the Knob Insert (92) into the left side of the left Upright. Use a rubber mallet, if necessary. Next, insert the pin into the Latch Insert, and tighten the knob back onto the pin. 77 92 5 Knob 85 Pin Collar Spring 6. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place; the allen wrench is used to adjust the walking belt (see page 26). To protect the floor or carpet from damage, place a mat under the treadmill. If you purchase the optional chest pulse sensor (see page 22), follow the steps below to install the receiver included with the chest pulse sensor. 1. Make sure that the power cord is unplugged. Remove the indicated Screw (7) and the Access Door (95) from the left side of the Console Back (98). 2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Back (98). Hold the receiver so the small cylinder is oriented as shown and is facing the Console Back. Attach the recei...