Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Keep children under age 12 and pets awayto slowly come to a complete stop. The ellipfrom the elliptical exerciser at all times. tical exerciser does not have a free wheel; the pedals will continue to move until theflywheel stops. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury orproperty damage sustained by or through the use of this product. 2 BEFORE YOU BEGIN Congratulations for selecting the new NordicTrack® CX 938 elliptical exerciser. The CX 938 is an incredibly smooth exerciser that moves your feet in a naturalelliptical path, minimizing the impact on your kneesand ankles. And the unique CX 938 offers an impressive array of features to help you achieve your fitnessgoals in the convenience of your home. Welcome to awhole new world of natural, elliptical-motion exercisefrom NordicTrack. For your benefit, read this manual carefully beforeyou use the elliptical exerciser. If you have ques tions after reading this manual, see the front cover ofthis manual. To help us assist you, please note theproduct model number and serial number before contacting us. The model number is 30621.0. The serialnumber can be found on a decal attached to the elliptical exerciser (see the front cover of this manual forthe location of the decal). Before reading further, please familiarize yourself withthe parts that are labeled in the drawing below. Handlebar BACK RIGHT SIDE Wheel Pedal Fan Upright Water Bottle Holder* *No Water Bottle is included. Leveling Foot Pedal Leg Handgrip Pulse Sensor Console The warning decalshown here has been placed on the ellipticalexerciser. If the decal is missing or illegible, callthe toll-free telephonenumber on the front cover of this manual and order a free replacement decal. Apply the decal in thelocation shown. ELLIP/BIKE NON FREEWHEEL209489and2101252DUFRITSPG 3 ASSEMBLY Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove thepacking materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included hex keys and your own phillips screwdriver mallet and rubber . As you assemble the elliptical exerciser, use the drawings below to identify the small parts used in assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST on page 21. The number after the key number is the quantity used in assembly. Note: Some small parts may have beenpreassembled. If a part is not in the parts bag, check to see if it is preassembled. M8 x 56mm Button Screw (83)–4M8 x 79mm Bolt Set (65)–2M10 x 108mm Button Screw (70)–2M10 SplitWasher (73)–27.6mm Spacer(47)–2M4 x 16mmRound HeadScrew (69)–4M8 SplitWasher (85)–4M4 x 16mmScrew (94)–2M8 x 44mm ButtonScrew (84)–8 1. Identify the Front Stabilizer (8). While another personlifts the front of the Frame (1) and holds the PedalLegs (4, 5) in the position shown, attach the FrontStabilizer to the Frame with four M8 x 44mm Button Screws (84) and a Support Plate (64). While another person lifts the rear of the Frame (1), attach the Rear Stabilizer (not shown) to the Framein the same way. 1 8 4, 51 64 84 84 4 2. Have another person hold the Upright (2) in the posi2 tion shown. Connect the Upper Wire Harness (30) to the Lower Wire Harness (42). Insert the connectors on the Wire Harnesses up into the Upright (2). Carefully pull the upper end of the Upper Wire Harness to remove the slack from the Wire Harnesses. Insert the Upright (2) into the Frame (1). Be careful to avoid pinching the Wire Harnesses (30, 42). Attach the Upright with two M10 x 108mm Button Screws (70), two M10 Split Washers (73), and two 7.6mm Spacers (47). Make sure that the curved sides of the Spacers are facing the Upright. Be careful to avoid damaging the Wire Harnesses with the Button Screws. Do not tighten the Button Screws yet. 2 3070 Pull 42 1 73 73 47 47 Do not pinch thewire harnesses during this step. 3. Slide a Weld Spacer (28) onto the axle on the left sideof the Upright (2), with the open side of the WeldSpacer facing the Upright. Apply a small amount of theincluded grease to the axle. Slide an Upper Body Arm (29) onto the axle on the leftside of the Upright (2). Using the included Push NutTool (96), tap a Push Nut (31) onto the axle; make sure that the Push Nut is turned as shown in the inset drawing. Attach the other Upper Body Arm (29) to the rightside of the Upright (2) in the same way. 4. Look inside one of the Handlebar Cover Sets (26) andlocate the square tabs connecting the two halves. Gently lift the tabs and disconnect the halves. Hold the two halves of the Handlebar Cover Set (26) around the tube on the left side of the Upright (2). Alignthe halves and press them together until they lock. Attach the other Handlebar Cover Set (26) to...