Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
While another person lifts the front of the Frame (1), attach the Front Stabilizer (4) to the Frame with two M10 x 78mm Carriage Bolts (92) and two M10 Nylon Locknuts (82). 4 92 82 82 1 5 2. Attach the Left and Right Frame Covers (36, 37) 2 around the Frame (1) with four M4 x 16mm Round Head Screws (80). 80 80 36 37 1 3. With the help of another person, carefully tip the elliptical exerciser onto its side. Attach the Center Foot (40) to the Frame (1) with two M4 x 16mm Screws (78). Then, return the elliptical exerciser to the upright position. Orient the Rear Stabilizer (3) as shown. While another person lifts the Folding Frame (2), attach the Rear Stabilizer to the Folding Frame with two M10 x 80mm Button Screws (93) and two M10 Split Washers (99). 3 99 99 78 40 2 933 1 6 4. While another person holds the Upright (10) near the Frame (1), connect the Upper Wire Harness (65) to the Lower Wire Harness (64). Then, insert the Upright (10) into the Frame (1). Attach the Upright with four M8 x 19mm Button Screws (85) and four M8 Split Washers (97). Do not tighten the Button Screws yet. Avoid pinching the Wire Harnesses (64, 65) during this step. 4 Avoid pinching the Wire Harnesses (64, 65) during this step 85 10 1 97 97 97 97 85 65 64 5. Orient the Left and Right Upright Covers (19, 20) as shown. Then, attach the Upright Covers around the Upright (10) with five M4 x 16mm Round Head Screws (80). 5 19 20 10 80 80 80 7 6. Apply a generous amount of the included grease to the Upper Body Axle (71). Insert the Upper Body Axle into the Upright (10). Be careful not to damage the Upper Wire Harness (65). Apply a small amount of grease to a Wave Washer (101). Slide the Wave Washer onto the left end of the Upper Body Axle (71). Identify the Left Upper Body Leg (24), which is marked with a sticker, and orient it as shown. Slide the Left Upper Body Leg onto the left side of the Upper Body Axle (71). Attach the Left Upper Body Leg (24) to the Upper Body Axle (71) with an M8 x 19mm Button Screw (85) and an M8 x 23mm x 2mm Washer (96). Repeat this step for the Right Upper Body Leg (72). 7. Attach the Left Upper Body Arm (22) to the Left Upper Body Leg (24) with three M8 x 14mm Button Screws (84) and three M8 Split Washers (97). Attach the Right Upper Body Arm (23) in the same way. 22 23 24 97 97 6 65 96 85 24 72 71 101Grease 85 101 10 96 Grease 7 84 8 9 8. Hold the Left Rear Upper Body Cover (26) and the Left Front Upper Body Cover (27) around the Left Upper Body Leg (24). Attach the Upper Body Covers with five M4 x 16mm Round Head Screws (80). Attach the Right Rear Upper Body Cover (28) and the Right Front Upper Body Cover (29) in the same way. 24 80 80 80 26 28 27 8 9 29 9. The Console (11) can be operated with four 1.5V “D” batteries (not included); alkaline batteries are recommended. IMPORTANT: If the ellipical exerciser has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries into the Console. If you do not do this, the console displays or other electronic components may become damaged. Remove the battery cover and insert four batteries into the Console. Make sure that the batteries are oriented as shown at the right. Then, reattach the battery cover. The Console (11) can also be operated with a regulated 6-volt DC 2-amp power supply (not included). To purchase a power supply, call your local Sears store. To avoid damaging the console, use only a manufacturer-supplied power supply. Plug one end of the power supply into the jack on the console; plug the other end into an outlet installed in accordance with all local codes and ordinances. Battery Cover Batteries 11 10. While another person holds the Console (11) near the Upright (10), connect the console wire harness to the Upper Wire Harness (65). Attach the Console (11) to the Upright (10) with four M4 x 16mm Screws (78). Avoid pinching the wire harnesses during this step. 10 78 65 Console Wire Harness 11 10 Avoid pinching the wire harnesses during this step 11. Orient a Link Arm (30) as shown. Attach the 11 Left Pedal (34) to the Link Arm with three M8 x 45mm Button Screws (90), three M8 Split Washers (97), and three M8 x 23mm x 2mm Washers (96). Attach a Pedal Arm Cover (39) to the Link Arm (30) with an M4 x 16mm Round Head Screw (80). Repeat this step for the Right Pedal (not shown) and the other Link Arm (not shown). 34 96 96 97 97 90 30 80 39 10 12. Apply a generous amount of grease to the axle on the Left Upper Body Leg (24) and to the axle on the left Crank Arm (55). Then, apply grease to two Large Wave Washers (102). Slide an Upper Body Leg Spacer (9) and a Large Wave Washer (102) onto the Left Upper Body Leg (24). Make sure that the flat side of the Upper Body Leg Spacer is facing outward. Then, slide the other Large Wave Washer onto the left Crank Arm (55). Slide the left Pedal Arm (32) onto the Left Upper Body Leg (24) while sliding the left Link Arm (30) onto the axle on the left Crank Arm (55). Attach the Pedal Arm ...