Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
5. Do not bend the strips inside the chest strap. This can cause the chest strap to loose conductivity. 6. The chest strap has batteries that need to be replaced periodically. A faulty battery can cause inaccurate reading. 4 5 Thank You for purchasing the Keys Fitness CG2 Elliptical! The quality product you have chosen was designed to meet your needs for cardiovascular exercise. Before you start, please read the Owner’s Manual and become familiar with the operation of your new unit. Remember to take time to perform stretching exercises, provided in this manual, to help avoid injury. If you are taking medication, consult your physician to see what affect the medication will have on your exercise heart rate. If you have heart problems, your are not active, and/or are over the age of 35 years, do not use the pre-set programs or start an exercise program without first contacting and receiving approval from your physician. To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys Fitness recommends a sealed water bottle for beverages consumed while using the unit. Assembly Please review the following drawing below to familiarize yourself with the listed parts. CONSOLE LEVELER FEET 2 PER SIDE PEDALS PULSE GRIP HANDLEBARS HANDLEBARS 6 Getting Started - The Keys Fitness CG2 Elliptical will require some assembly. Unpack the box in a clear area. Remove packing material. Do not dispose of packing material until assembly is complete and unit is working properly. Place the unit on a clean level surface for assembly. Make sure there is easy access to an electrical outlet. Before assembling the unit should be placed as close as possible to its final location. Tools have been provided for use while assembling this product. Assembly Parts 1. Owner’s Manual 2. Linkage 3. Left and Right Handlebars 4. Console 5. Console Cable 6. Console Mast 7. Rear Cover 8. M8*50mm Hex Bolt - Qty 3 9. M8*12mm Hex Bolt - Qty 4 10. M8*20mm Hex Bolt - Qty 6 11. M5*12mm Screw - Qty 9 Assembly Figure 1 Lift pedal and place left Linkage onto Sleeve and align holes. Secure Linkage to unit using four M8*12 mm Hex Bolts. Note: Left Linkage will be wrapped in plastic. Right Linkage will already be secured to the sleeve. LINKAGE SLEEVE M8*12MM HEX BOLT 7 Assembly Figure 2 Attach Handlebars to Main Frame using three M8*20mm Hex Bolts. Repeat for other handlebar. M8*20mm Hex Bolt Right Handlebar Left Handlebar Figure 2 Figure 3 Remove Rear Cover from unit by removing five screws. Figure 3 8 Assembly Figure 5 Connect 7 Pin, 3 Pin and Grounding cables.. Refer To Figure 5 and 5a. Attach Console to Console tube using four M5*12mm Philip Head Screws. Note: Ensure that all wires are secure inside console. Be careful not to pinch wires. 7 PIN CONNECTOR M8*50mm Hex Bolt 7PIN CONNECTOR Console Mast Figure 4 Attach Console Tube to Main Frame. Slide Tube down into Main Frame. Secure using three M8*50mm Hex Head Bolts. Cable should extend thru bottom and top of Console Tube. Figure 4 3 PIN CONNECTOR CONSOLE CABLES 7 PIN CONNECTOR 3 PIN CONNECTOR 2 GROUND CONNECTORS Figure 5a Figure 5 GROUNDING TERMINALS 9 Assembly CONGRATULATIONS! You have completed assembly of your CG2 Elliptical Figure 6 Attach Rear Cover to Main Frame using five M5*12mm Philip Head Screws removed in figure 3. Note: Do not force Rear Cover back into place, this will damage Rear Cover. Figure 6 REAR COVER M5*12MM SCREW Figure 7 Level machine so that no wobble is present. Leveler feet screw in and out to level machine. After machine is level, tighten leveler nut to secure levelers in place. Figure 7 LEVELER Console Instructions Take a few moments to review the console layout. Below is a overview of the console keys and their different functions. BUTTON OVERVIEW START Press to enter Quick Start Mode. In Pause Mode, used to resume exercise session.. ENTER/SCAN - In Program Mode, used to confirm the values you set. During exercise, pressed once, will place the main console window in Auto Scan Mode. The display will change every four seconds from TIME/DISTANCE/SPEED/STRIDES PER MIN to CALORIES/PULSE/LEVEL/CAL/HR. To exit Auto Scan Mode and enter Manual Scan Mode, Press and Hold button for two seconds. Console will beep twice. Manual Scan Mode allows you to toggle display from TIME/DISTANCE/SPEED/STRIDES PER MIN to CALORIES/PULSE/LEVEL/CAL/ HR by pushing the ENTER/SCAN button. To return to Auto Scan Mode, Press and Hold button for two seconds. Console will beep twice to confirm switch. 10 Console Instructions PAUSE/RESET - During exercise, used to Pause workout. In Pause mode, used to reset program time and workout data to zero. In Program mode, used to Reset values to the default. Caution: In User 1 and User 2 programs, the user profile data will be cleared also. “+”/”-” - In Program mode, used to increase/decrease TIME, WEIGHT and AGE. During exercise, used to increase/decrease the resistance level from 1 to 20. Press and Hold for two seconds to rapidl...