Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• This ellptical trainer has a user maximum capacity of 300 pounds. • The Keys Elliptical Trainer should only be used on a level surface and is intended for indoor use only. It should not be placed in a garage, patio or near water. Keys recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this exercise unit with bare feet, sandals, socks or stockings! • Always examine your elliptical trainer before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the exercise unit. • Never operate the elliptical trainer where oxygen is being administered or where aerosol products are being used. • Never insert any object or body parts into any opening. • Service to your Keys Elliptical Trainer should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys technician. Failure to follow these instructions will void the warranty. 3 Assembly of CardioMax 850 Elliptical Trainer Assembly of CardioMax 850 Elliptical Trainer 1 REMOVE ALL SECURITY TAPE AND WRAPPING BEFORE BEGINNING. 1. Attach the Aluminum Extrusions (45) to the Main Frame Assembly (1) with Screws (63). Connect the Aluminum Extension Plate (34) between the Extrusions (45) with Screws (64). 2. Attach both the Left and Right Rear Foot Frames (32, 33) to the Left and Right Front Foot Frames (30,31) with Carriage Bolts (62) and Locknuts (49). 2 4 5 4343 3. First connect the Controller Extension Wire (27). Then slide the Main Upright (2) onto the Main Frame Assembly (1) and secure with Screws (56), Flat Washers (50) and Locknuts (49). 4. Feed the two Pulse Wires (26) from the Console (5) down into the Main Upright (2) and out the handlebar hole. Connect the Controller Wire (28) to the Console (5). Then connect the Monitor (5) to the Main Upright (2) with Screws (59). 67 5656 5. First connect the Pulse Wires (26) to the T-Shaped Handlebar (10). Then connect the T-Shaped Handlebar (10) to the Main Upright (2) with Screws (55), Flat Washers (50) and Locknuts (49). 6. Curved Washers (79) should already be on Main Upright posts. Slide the left and right handlebars (3, 4) onto the Main Upright (2). Secure handlebars with Washers (61), Snap Caps (21), Washers (69), Nuts (52), and Nut Caps (22). 89 7878 7. Secure the Connecting Arms (29) to the left and right 8. Insert the batteries provided into the back of the Monitor (5) handlebars (3, 4) with Screws (67), Washers (69), Caps (68), and Nuts (52). 10 11 13 9 9. You have completed the assembly of your CardioMax 850 Elliptical Trainer. 12 850 ELLIPTICAL PARTS LIST NO. PART 1 MAIN FRAME ASSEMBLY 2 MAIN UPRIGHT 3 LEFT FOAM HANDLE 4 RIGHT FOAM HANDLE MONITOR 6 PULLEY 7 GENERATOR 8 CONTROLLER BOARD 9 V-BELT T-SHAPED HANDLEBAR 11 BOTTOM LEFT HOUSING 12 BOTTOM RIGHT HOUSING 13 TOP HOUSING 14 CONSOLE TUBE COLLAR ROUND COVER 16 ROOT PEDAL 17 END CAP 18 ROLLER CAP 19 FOOT CAP WHEEL 21 SNAP CAP 22 NUT CAP 23 38mm BALL PLUG 24 31.8mm BALL PLUG HAND PULSE 26 PULSE WIRE 27 CONTROLLER EXTENSION WIRE 28 CONTROLLER WIRE 14 QTY 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 2 2 2 1 NO. 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 PART QTY CONNECTING ARM 2 LEFT FRONT FOOT FRAME 1 RIGHT FRONT FOOT FRAME 1 LEFT REAR FOOT FRAME 1 RI GHT REAR FOOT FRAME 1 ALUMINUM EXTENSION PLATE 1 6004 PRECISE BEARING 6 608 PRECISE BEARING 8 38mm HANDLEBAR SLEEVE 2 76mm BUSHING 4 BELT TENSION BRACKET 1 ADJUSTMENT CHANNEL 2 EYEBOLT 3 SPRING 1 IDLER PULLEY 1 ROLLER 2 ALUMINUM EXTRUSION 2 M6 LOCKNUT 4 M6 HEX NUT 3 M10 CAP NUT 2 M8 LOCKNUT 10 M8 IDX18.8mm OD FLAT WASHER 12 51 M20X32X2mm WASHER 4 52 M10 NUT 10 53 M8X17mm SCREW 1 54 M8X38mm SCREW 1 55 M8X57mm SCREW 2 56 M8X60mm SCREW 3 15 850 ELLIPTICAL PARTS LIST CONTINUED NO. PART QTY NO. PART 70 25mm BUSHING 57 TP4X12mm SCREW 46 71 NUT CAP 58 TP5X50mm SCREW 4 72 CRANK NUT 59 M5X10mm SCREW 4 73 LEFT CRANK 60 M6X15mm 8 74 RIGHT CRANK 61 M10X38 WASHER 4 75 SHAFT BUSHING 62 M8X80mm CARRIAGE BOLT 4 76 JOINITER 63 M8X100 mm SCREW 4 77 M8X30mm WASHER 64 M8X15mm SCREW 6 78 RETAINING RING 65 M10X55-8mm SCREW 2 79 M26 CURVED WASHER 66 M10X48 MACHINE SCREW 2 80 M16X28 WASHER 67 M10X58mm SCREW 2 81 M8 NUT 68 15.8X10X4.3 CAP 4 82 38mm END CAP 69 M10X23mm WASHER 4 83 31.8mm END CAP 84 13.7 X 10X8 CAP QTY 8 4 2 1 1 2 2 2 2 4 2 3 2 2 4 850 Display Instructions Your Keys Elliptical Trainer 850 is equipped with a programmable monitor to help you track your progress and motivate you to reach your fitness goals. In order to set your programmable monitor, you must begin stepping. The monitor will come to life and prompt you for the following: 16 17 850 DISPLAY INSTRUCTIONS CONTINUED ENTER WEIGHT Use the up and down arrows to set your weight, then press the Enter key. SELECT PROGRAM Use the up and down arrows to scroll through the optional programs. Once the desired program is d...