Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
STEP 1 (See Diagram 1) A.) Attach a Rear Stabilizer (#11) to the bottom of the Upright Beam (#9). Secure it with one Bracket (#15), four M10 x 2 .” Carriage Bolts (#12), . .” Washers (#13) and M10 Aircraft Nuts (#14). Repeat the same step for the other side. B.) Place the Backrest Adjustment Bar (#7) on the selected bar holder on the Upright Beam (#9) to obtain desired incline of Backrest. C.) Insert two Crutches (#4) into the top openings on the Upright Beams (#9). Secure them with two Lock Knobs (#6) through selected holes to obtain desired height of the Crutches. Make sure both sides are at the same height. DIAGRAM 1 4 STEP 2 (See Diagram 2) A.) Attach the rear of the Main Seat Support (#25) to the Upright Beam (#9). Secure it with two M10 x 2 .” Allen Bolts (#16), four . .” Washers (#13), and two M10 Aircraft Nuts (#14). Do not tighten the nuts and bolts yet. B.) Slide the Sliding Block (#22) onto the Main Seat Support (#25). Secure it with a Lock Knob (#6). C.) Attach the Front Stabilizer (#40) to the Main Seat Support. Secure it with three M10 x 2 .” Allen Bolts (#16), six . .” Washers (#13), and three M10 Aircraft Nuts (#14). D.) Insert one Lock Knob (#6) into the hole on the back of Front Stabilizer (#40). E.) Securely tighten all the nuts and bolts previously installed. DIAGRAM 2 5 STEP 3 (See Diagram 3) A.) Attach two Seat Supports (#20), one on each side, to the pivot on the Sliding Block (#22). Secure the Seat Supports (#20) to the two rear holes on the Seat Pad (#1) using two M8 x 1 3/4” Allen Bolts (#18) and . .” Washers (#19). B.) Attach the Seat Incline Adjustment (#27) to the two front holes on the Seat Pad. Secure it with two M8 x 1” Allen Bolts (#26) and .1/2” Washers (#19). Place the Seat Incline Adjustment onto the Sliding Block. Insert a L-shaped Pin (#28) into the selected holes on the Seat Incline Adjustment to hold the desired incline. C.) Attach two Backrest Supports (#17), one on each side, to the pivot on the Sliding Block (#22). Place Backrest Board (#2) onto the Backrest Supports (#17). Secure it with four M8 x 1 .” Allen Bolts (#18) and . .” Washers (#19). DIAGRAM 3 6 STEP 4 (See Diagram 4) A.) Insert the Leg Developer Holder (#41) into the opening on the Front Stabilizer (#40). Secure it with the Lock Knob (#6). B.) Attach the Leg Developer (#38) to the bracket on the Leg Developer Holder (#41). Secure it with a M12 x 2 3/8” Axle (#36) and M12 Allen Bolt (#45). C.) Secure the Leg Developer (#38) with a 4” Lock Pin (#36). Remove the Pin when using the Leg Developer. D.) Insert a Foam Roll Tube (#32) halfway through the hole on the Leg Developer Holder (#41). Insert two Foam Roll Tubes (#32) halfway through the holes on the Leg Developer (#38). E.) Push six Foam Rolls (#33) onto the Tubes from both sides. Plug six Foam Roll End Caps (#34) to the ends. F.) Attach the Olympic Sleeve (#5) onto the weight post on the Leg Developer. Attach the Spring Clip (#44) onto the Olympic Sleeve. DIAGRAM 4 7 8 PARTS LIST KEY NO. DESCRIPTION Q’ty Seat Pad 1 Backrest Board 1 2” x 2 .” Sleeve 2 Crutch 2 Olympic Sleeve 1 Lock Knob 4 Backrest Adjustment Bar 1 1 .” Square End Cap 2 Upright Beam 1 2” End Cap 6 Rear Stabilizer 2 M10 x 2 .” Carriage Bolt 8 . .” Washer 18 M10 Aircraft Nut 13 Bracket 2 M10 x 2 .” Allen Bolt 3 Backrest Support 2 M8 x 1 .” Allen Bolt 6 . .” Washer 8 Seat Support 2 1” Square End Cap 4 Sliding Block 1 Sliding Block Sleeve 2 M10 x 3” Allen Bolt 2 Main Seat Support 1 M8 x 1” Allen Bolt 2 Seat Incline Adjustment 1 L-shaped Pin 1 Bearing 2 2” Square Sleeve 1 1 .” Square End Cap 1 Foam Roll Tube 3 Foam Roll 6 Foam Roll End Cap 6 4” Lock Pin 1 M12 x 2 3/8” Axle 1 Spring Clip Sleeve 2 Leg Developer 1 1 3/8” x 2 3/8” End Cap 2 Front Stabilizer 1 Leg Developer Holder 1 Rubber End Cap 1 Allen Set Screw 1 Spring Clip 1 M12 Allen Bolt 1 9 IRON GRIP SPORT By IMPEX FITNESS PRODUCTS LIMITED LIFE TIME WARRANTY IMPEX FITNESS PRODUCTS ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of LIFE TIME on the Frame and Weld, 3 YEARS on parts, and 6 MONTHS on upholstery from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for heavy commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or ...