Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
12. A spotter is recommended during exercise. WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 HARDWARE PACK 3 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left Upright Beam (#1) and Right Upright Beam (#2) by a Cross Brace (#3) in the mid-span. Align the holes and secure each end of the Cross Brace with one 4 .” x 2” Bracket (#16), two M10 x 3 .” Carriage Bolts (#33), two . .” Washers (#43), and two M10 Aircraft Nuts (#47). B.) Place the Backrest Adjustment Bar (#5) in between the two Upright Beams on the selected bar holder to obtain desired incline of Backrest Board. C.) Insert two Crutches (#7) into the top openings on the Upright Beams. Push down the Plastic Sleeve (#31) until it locks in place. Secure the Crutches with two Lock Knobs (#30) through selected holes to obtain desired height of the Supports. DIAGRAM 1 4 STEP 2 (See Diagram 2) A.) Attach the Main Stabilizer (#13) to the Cross Brace (#3). Secure it with a 4 3/8” x 1 .” Bracket (#15), two M10 x 2 1/8” Carriage Bolts (#35), . .” Washers (#43), and M10 Aircraft Nuts (#47). B.) Attach the Front Support (#10) to the Main Stabilizer (#13). Secure it with one M10 x 2 3/8” Allen Bolt (#38) and . .” Washer (#43). C.) Attach one end of Man Seat Support (#4) to the Main Stabilizer (#13). Secure it with two M10 x 2 .” Carriage Bolts (#34), . .” Washers (#43), and M10 Aircraft Nuts (#47). D.) Attach the other end of Main Seat Support (#4) to the Front Support (#10). Secure it with two M10 x 1” Carriage Bolts (#36), . .” Washers (#43), and M10 Aircraft Nuts (#47). DIAGRAM 2 5 STEP 3 (See Diagram 3) A.) Attach the hole-side of Backrest Supports (#9) to the pivot on the Main Seat Support (#4). Secure it with one M12 x 6” Hex Bolt (#40), two O1” Washers (#42), and one M12 Aircraft Nut (#46). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar. B.) Place the Backrest Board (#17) onto the Backrest Supports (#9). Secure it with four M6 x 1 3/8” Hex Bolts (#41) and ..” Washers (#45). C.) Place the Seat (#18) onto the Main Seat Support (#4). Secure it with four M6 x 1 3/8” Hex Bolts (#41) and . .” Washers (#45). DIAGRAM 3 6 STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#6) to the open bracket on the Front Support (#10). Secure it with one M10 x 2 7/8” Allen Bolt (#37), two . .” Washers (#43), and one M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#8) halfway through the holes on the Leg Developer. Push four Foam Rolls (#20) onto the Foam Tubes. C.) Attach the Bar Holder (#12) to the Leg Developer (#6). Secure it with a L-shaped Pin (#48). Remove the Bracket when using the Leg Developer. D.) Attach the Arm Curl Pad (#19) to the Arm Curl Stand (#11) then secure it with two M8 x 5/8” Allen Bolts (#39) and two . 5/8” Washers (#44). E.) Insert the Arm Curl Stand (#11) into the top opening on the Front Support (#10). Secure it with a Lock Knob (#30). Use the Lock Knob to select the Arm Curl height. F.) Attach a Spring Clip (#49) to the weight post on the Leg Developer. Attach two Spring Clips (#49) to the Curl Bar (#14). DIAGRAM 4 7 8 PARTS LIST KEY NO. DESCRIPTION Q’ty 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 26 27 28 29 31 32 33 34 36 37 38 39 41 42 43 44 46 47 48 49 Left Upright Beam 1 Right Upright Beam 1 Cross Brace 1 Main Seat Support 1 Backrest Adjustment Bar 1 Leg Developer 1 Crutch 2 Foam Tube 2 Backrest Support 2 Front Support 1 Arm Curl Stand 1 Bar Holder 1 Main Stabilizer 1 Curl Bar 1 4 3/8” x 1 .” Bracket 1 4 .” x 2” Bracket 2 Backrest Board 1 Seat 1 Arm Curl Pad 1 Foam 4 1 .” Square End Cap 2 1 .” Square End Cap 2 1” Square End Cap 2 . 1” End Cap 1 . 1” Cone-shape End Cap 3 . .” Cone-shape End Cap 4 2 .” x 2” End Cap 4 1 .” x 1 .” Sleeve 1 Plastic Bushing 2 Lock Knob 3 3” x 2 .” Sleeve 2 Crutch End Cap 2 M10 x 3 .” Carriage Bolt 4 M10 x 2 .” Carriage Bolt 2 M10 x 2 1/8” Carriage Bolt 2 M10 x 1” Carriage Bolt 2 M10 x 2 7/8” Allen Bolt 1 M10 x 2 3/8” Allen Bolt 1 M8 x 5/8” Allen Bolt 2 M12 x 6” Hex Bolt 1 M6 x 1 3/8” Hex Bolt 8 O 1” Washer 2 O .” Washer 13 O 5/8” Washer 2 O .” Washer 8 M12 Aircraft Nut 1 M10 Aircraft Nut 11 L-shaped Pin 1 Spring Clip 3 Philips Screw 4 9 IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purc...