Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3 HARDWARE PACK 4 HARDWARE PACK 5 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1 & 2) by a Cross Brace (#3) in the mid-span. Align the holes and secure each end of the Cross Brace with one 4 .” x 2 .” Bracket (#20), two M10 x 2 .” Carriage Bolts (#43), two . .” Washers (#39), and two M10 Aircraft Nuts (#50). B.) Place Backrest Adjustment Bar (#8) between the two Upright Beams. C.) Insert two Crutches (#7) into the top openings on the Upright Beams. Secure them with two M18 Lock Knobs (#26) through selected holes to obtain desired height of the Supports. D.) Push four 2 .” x 2” End Caps (#25) onto the ends of the two Upright Beams. DIAGRAM 1 6 STEP 2 (See Diagram 2) A.) Attach Main Seat Support (#4) to the Cross Brace (#3). Secure it with a 4 3/8” x 1 .” Bracket (#19), two M10 x 2 .” Carriage Bolts (#42), two . .” Washers (#39), and two M10 Aircraft Nuts (#50). B.) Attach the Leg Developer Holder (#5) to the Main Seat Support (#4). Secure it with two M10 x 2 .” Carriage Bolts (#42), . .” Washers (#39), and M10 Aircraft Nuts (#50). C.) Insert a M12 x 5 .” Hex Bolt (#45) through the hole on the Right Butterfly (#10). Secure the Bolt with a M12 Regular Nut (#41). Insert the Bolt through the hole on the Right Upright Beam (#2) and secure with a M12 Lock Knob (#27). D.) Insert a Butterfly Handle (#15) through the hole on the Right Butterfly from the rear. Push a . 2 .” Foam Roll (#22) onto the Handle. Attach a Spring Clip (#24) to the weight post on the Right Butterfly. E.) Repeat the Procedures C, D, and E above to install the Left Butterfly (#9). DIAGRAM 2 7 STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#11) to the Leg Developer Holder (#5). Secure it with an Axle (#54), two M10 x 5/8” Allen Bolts (#47), and two . .” Washers (#39). B.) Insert two Foam Tubes (#14) halfway through the holes on the Leg Developer. Push four . 4” Foam Rolls (#23) onto the Tubes from both ends. C.) Attach a Spring Clip (#24) onto the weight post on the Leg Developer. D.) Attach the Arm Curl Pad (#18) to the Arm Curl Stand (#12). Secure it with two M8 x 5/8” Allen Bolts (#48) and . 5/8” Washers (#38). E.) Insert the Arm Curl Stand into the opening on the Leg Developer Holder. Secure it with a M18 Lock Knob (#26) through a selected hole to obtain the desired height for Arm Curl exercise. DIAGRAM 3 8 STEP 4 (See Diagram 4) A.) Attach the two side-holes on the two Backrest Supports (#13) to the pivot on the Main Seat Support (#4). Align the holes and secure it with one M12 x 7 .” Hex Bolt (#44), two . 1” Washers (#40), and one M12 Aircraft Nut (#51). B.) Place the Backrest Board (#16) onto the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#49) and . 5/8” Washers (#38). C.) Attach the Seat (#17) to the two Seat Brackets (#6) and secure with four M8 x 1 5/8” Allen Bolts (#49) and . 5/8” Washers (#38). D.) Place the Seat Brackets onto the Main Seat Support (#4). Align the holes and secure each Seat Bracket to the Main Seat Support with one M10 x 2 .” Allen Bolt (#46), two O .” Washers (#39), and one M10 Aircraft Nut (#50). DIAGRAM 4 9 10 PARTS LIST KEY NO. DESCRIPTION Q’ty 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 26 27 28 29 31 32 33 34 36 37 38 39 41 42 43 44 46 47 48 49 51 52 53 54 Left Upright Beam 1 Right Upright Beam 1 Cross Brace 1 Main Seat Support 1 Leg Developer Holder 1 Seat Bracket 2 Crutch 2 Backrest Adjustment Bar 1 Left Butterfly 1 Right Butterfly 1 Leg Developer 1 Arm Curl Stand 1 Backrest Support 2 Foam Tube 2 Butterfly Handle 2 Backrest Board 1 Seat 1 Arm Curl Pad 1 4 3/8” x 1 .” Bracket 1 4 .” x 2 .” Bracket 2 . 1 .” Rubber Bumper 1 O 2 .” Foam Roll 2 O 4” Foam Roll 4 Spring Clip 3 2 .” x 2” End Cap 4 M18 Lock Knob 3 M12 Lock Knob 2 . 5/8” Bushing 4 Upright Beam Sleeve 2 Inner Cap 2 . 1 .” x 2” Rubber Bumper 2 1” Square End Cap 2 2” Sleeve 1 1 .” Square End Cap 4 1 .” Square End Cap 2 . 1” Cone-shaped End Cap 7 . 1” End Cap 6 . 5/8” Washer 10 . .” Washer 14 . 1” Washer 2 M12 Regular Nut 2 M10 x 2 .” Carriage Bolt 4 M10 x 2 .” Carriage Bolt 4 M12 x 7 .” Hex Bolt 1 M12 x 5 .” Hex Bolt 2 M10 x 2 .” Allen Bolt 2 M10 x 5/8” Allen Bolt 2 M8 x 5/8” Allen Bolt 2 M8 x 1 5/8” Allen Bolt 8 M10 Aircraft Nut 10 M12 Aircraft Nut 1 ST2 Philips Screw 4 Bushing 2 Axle 1 11 IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal...