Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
11. Never operate the machine if the machine is not functioning properly. 12. A spotter is recommended during exercise. CARE AND MAINTENANCE 1. Lubricate moving parts with WD-40 or light oil periodically. 2. Inspect and tighten all parts before using the machine. 3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents. 4. Maximum weight capacity 300 lbs. WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Rear Upright Beam. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3 HARDWARE IDENTIFIER 4 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Plug the two Stabilizer End Caps (#23) onto the bottom of the two Rear Upright Beams (#1). B.) Connect the two Rear Upright Beams by a Cross Brace (#2) in the Mid-span. Secure them with two M10 x 3 1/8” Carriage Bolts (#26), one Curved Bracket (#3), two . .” Washers (#32), and two M10 Aircraft Nuts (#35) on each end of the Cross Brace. C.) Insert the Backrest Adjustment Bar (#4) through a selected hole to obtain desired incline of Backrest. DIAGRAM 1 5 STEP 2 (See Diagram 2) A.) Plug a Stabilizer End Cap (#23) onto the bottom of Front Leg (#8). Attach the Front Leg to the Main Seat Support (#6). Secure it with three M8 x 5/8” Allen Bolts (#30) and O 5/8” Washers (#33). DO NOT tighten the Bolts yet. B.) Attach the Main Seat Support (#6) to the Cross Brace (#2). Secure it with two M10 x 2 1/8” Carriage Bolts (#27), one Flat Bracket (#5), two O .” Washers (#32), and two M10 Aircraft Nuts (#35). C.) Attach one end of Diagonal Support (#7) to the Main Seat Support (#6). Secure it with one M8 x 2 1/8” Allen Bolt (#29), two O 5/8” Washers (#33), and one M8 Aircraft Nut (#36). Attach the other end of Diagonal Support to the Front Leg (#8). Secure it with one M8 x 5/8” Allen Bolt (#30) and O 5/8” Washer (#33). D.) Securely tighten all Nuts and Bolts previously installed. DIAGRAM 2 6 STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#10) to the Front Leg (#8). Secure it with one M8 x 3 1/8” Allen Bolt (#28), two O 5/8” Washers (#33), and one M8 Aircraft Nut (#36). B.) Insert two Foam Tubes (#11) halfway through the holes on the Leg Developer. Push four Foam Rolls (#19) onto the Tubes from both sides. C.) Place a Spring Clip (#22) onto the weight post on the Leg Developer. DIAGRAM 3 7 STEP 4 (See Diagram 4) A.) Attach the hole-side of the Backrest Supports (#13) onto both ends of the pivot on the Main Seat Support (#6). Place the other end rest against the Backrest Adjustment Bar (#4). B.) Place the Backrest Board (#14) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Philips Screws (#31) and O .” Washers (#34). C.) Place the Seat Pad (#15) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Philips Screws (#31) and O .” Washers (#34). DIAGRAM 4 8 STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#16) to the Arm Curl Stand (#12). Secure it with two M8 x 5/8” Allen Bolts (#30) and O 5/8” Washers (#33). B.) Insert the Arm Curl Stand into the top opening on the Front Leg. Secure it with a Lock Knob (#24). DIAGRAM 5 9 10 PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 2223 24 26 27 28 29 31 32 33 34 36 Rear Upright Beam 2 Cross Brace 1 Curved Bracket 2 Backrest Adjustment Bar 1 Flat Bracket 1 Main Seat Support 1 Diagonal Support 1 Front Leg 1 Curl Bar 1 Leg Developer 1 Foam Tube 2 Arm Curl Stand 1 Backrest Support 2 Backrest Board 1 Seat Pad 1 Arm Curl Pad 1 Round Sleeve 1 1” Round End Cap 10 Foam Roll 4 2” Round End Cap 2 Bushing 2 Spring Clip 3 Stabilizer End Cap 3 Lock Knob 1 1” Square End Cap 2 M10 x 3 1/8” Carriage Bolt 4 M10 x 2 1/8” Carriage Bolt 2 M8 x 3 1/8” Allen Bolt 1 M8 x 2 1/8” Allen Bolt 1 M8 x 5/8” Allen Bolt 6 M6 x 1 3/8” Philips Screw 8 O .” Washer 6 O 5/8” Washer 10 O .” Washer 8 M10 Aircraft Nut 6 M8 Aircraft Nut 2 11 IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPE...