Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Screw the FOOT STANDS(64) all the way up into the REAR STABILIZER(6) on both sides. STEP 5 Screw the STAND(68) all the way up into the bottom of the FRONT FRAME(1). Connect the PULSE EXTENSION WIRE(43) to the CONTROL WIRE(25). Insert the FRONT FRAME(1) into the REAR FRAME(5) and secure with BUTTON HEAD BOLTS(M10x1.5x20mm)(74), BUTTON HEAD BOLTS(M10x1.5x53mm) (75), ARC WASHERS(M10)(99), and LOCK WASHERS(M10)(101). Press the COVER PLUGS(67) into the holes in the LEFT and RIGHT REAR COVERS(65, 66). NOTE: See page 13 for detailed leveling instructions to prevent rocking. Rear Frame(5), is inside of Rear Covers(65, 66) 9 ASSEMBLY INSTRUCTIONS To attach the HANDRAIL(9), position the HANDRAIL(9) under the SEAT CARRIAGE(7) as shown in the above illustration and secure with BUTTON HEAD BOLTS(M8x1.25x45mm)(71), ARC WASHERS(M8) (98), and LOCK WASHERS(M8)(100). STEP 8 Refer to the inset drawing. Plug the PULSE SENSOR WIRE(55) into the SOCKET of the PULSE EXTENSION WIRE(43) located on the SEAT RAIL(45). STEP 7 NOTE: The PULSE SENSOR WIRES(55) go through the tube of the HANDRAIL(9). Be careful not to damage the wires when inserting the BUTTON HEAD BOLTS(M8x1.25x45mm)(71) through the holes in the HANDRAIL(9) when attaching it to the SEAT CARRIAGE(7). Socket of Pulse Extension Wire(43) STEP 6 Attach the SEAT FRAME(8) to the SEAT CARRIAGE(7) with BUTTON HEAD BOLTS(M10x1.5x200mm)(76), WASHERS(M10)(99), LOCK WASHERS(M10)(101), and ACORN NUTS(M10x1.5)(97). 10 ASSEMBLY INSTRUCTIONS STEP 9 Attach the SEAT(59) and BACK CUSHION(60) to the SEAT FRAME(8) with ROUND HEAD BOLTS (M6x1x38mm)(82). STEP 10 Refer to the inset drawing. Press the NUT CAPS(M10)(53) onto the NYLOCK NUTS(M10x1.5)(95) on both sides of the SEAT CARRIAGE(7). 11 ASSEMBLY INSTRUCTIONS STEP 11 NOTE: The RIGHT PEDAL(41) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(41) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(39) has L stamped on the end of the pedal shaft. The LEFT PEDAL(39) has left hand threads and is tightened by turning counterclockwise. Thread the RIGHT PEDAL(41) into the RIGHT CRANK(36) as shown. Tighten the pedal securely. Select the RIGHT PEDAL STRAP(42) which has R marked on it. Snap the two hole end to the inside edge of the RIGHT PEDAL(41). Insert the other end of the strap through the slot and snap the strap to the hook on the outside edge of the RIGHT PEDAL(41). Select adjustment holes which allow your foot to be easily removed from the pedals. Use the same procedure to attach the LEFT PEDAL(39) to the LEFT CRANK(35) and snap the LEFT PEDAL STRAP(40) to the LEFT PEDAL(39). STEP 12 Slide the UPRIGHT SLEEVE(32) over the UPRIGHT(3). Connect the CONNECTION WIRE(26) to the CONTROL WIRE(25). Insert the UPRIGHT(3) onto the FRONT FRAME(1) and secure with FLAT HEAD BOLTS(M8x1.25x15mm)(79). Slide the UPRIGHT SLEEVE(32) down to cover the bolt heads. 12 ASSEMBLY INSTRUCTIONS Socket of Power Wire(28) A. B. STEP 13 Refer to illustration A. Run the CONNECTION WIRE(26) through the hole in the plate on the HANDLEBAR(4). Attach the HANDLEBAR(4) to the UPRIGHT(3) with BUTTON HEAD BOLT(M8x1.25x40mm)(70) and FLAT HEAD SCREWS(M6x1x12mm)(78). STEP 14 Plug the CONNECTION WIRE(26) into the EXTENSION WIRE on the COMPUTER(27). Attach the COMPUTER(27) to the plate on the HANDLEBAR(4) with ROUND HEAD SCREWS(M5x0.8x15mm)(86). STEP 15 Attach the MOUNTING BRACKET(106) to the UPRIGHT(3) with ROUND HEAD SCREWS (M4x0.7x15mm)(85). Place the WATER BOTTLE(107) in the MOUNTING BRACKET(106). STEP 16 Refer to illustration B. Plug the ADAPTER(105) into the SOCKET of the POWER WIRE(28) located on the front of the bike. Plug the ADAPTER(105) into an electrical outlet. 13 SET UP INSTRUCTIONS Place the Magnetic Fusion 7250 Bike in the area where it will be used. It is recommended that the Magnetic Fusion 7250 Bike be placed on an equipment mat. The Magnetic Fusion 7250 Bike is approximately 55 3/4 inches long x 24 3/8 inches wide x 50 3/8 inches tall (max.). (These dimensions may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic Fusion 7250 Bike. Make sure that adequate space is available for access to and passage around the Magnetic Fusion 7250 Bike. To level the Magnetic Fusion 7250 Bike, first screw the STAND(68) located in the middle of the FRONT FRAME(1) all the way up into the FRONT FRAME(1) so that it is not touching the floor. Adjust the four FOOT STANDS(64) on each of the four corners, two under FRONT STABILIZER(2) and two under the REAR STABILIZER(6). When the FOOT STANDS(64) are adjusted and the Magnetic Fusion 7250 Bike is stable, rotate the STAND(68) to make it contact with the floor. While you are adjusting the FOOT STANDS(64) the STAND(68) must not be in contact with the floor. Only after the Magnetic Fusion 7250 Bike has been stabilized with the FOOT STANDS(64) will you position the STAND(68) so it is in contact with the floor to provide extra stability for the frame. The Magnetic ...