Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
NOTE: STEP 3: Make the tab in the edge of the OVAL ENDCAPS(58) face down, then press the OVAL ENDCAPS (58) into both ends of the front stabilizer of the MAIN FRAME(1). R L ASSEMBLY INSTRUCTIONS 8 STEP 5 CAUTION: Attach the UPRIGHT(3) to the MAIN FRAME(1) with the NYLOCK NUTS(M10x1.5)(84) and WASHERS (M10)(78). Plug the BASE CONNECTION WIRE(18) into the CONNECTION WIRE(19). STEP 6 Connect the LINKS(36) to the ROCKER ARMS(4) at both sides with D-SHAPED SHAFT(42), WASHERS (M6)(77), and BUTTON HEAD BOLTS(M6x1x12mm)(62). Be careful not to damage the BASE CONNECTION WIRE(18) and CONNECTION WIRE(19) when assembling the UPRIGHT(3). ASSEMBLY INSTRUCTIONS STEP 7 Place the LEFT NOSE COVER(34) and RIGHT NOSE COVER(35) at both sides of the UPRIGHT(3). Bolt the nose covers together with the ROUND HEAD SCREW(M5x0.8x35mm)(71) on the top. Then slide the nose covers down and attach them to the MAIN FRAME(1) with ROUND HEAD SCREW(M5x0.8x35mm)(71). STEP 8 Refer to the inset drawing. Lift up the RIGHT PEDAL ARM(7) slightly. Then place a ROLLER COVER(33) to cover the ROLLER(30). Snap the ROLLER COVER(33) into the slots at both sides of the ROLLER(30) in the MAIN FRAME(1). Repeat on the left side. 9 Slot ASSEMBLY INSTRUCTIONS 10 STEP 9 Attach the TRAY(56) to the bracket on the UPRIGHT(3) and secure with ROUND HEAD SCREWS (M5x0.8x15mm)(70). STEP 10 Attach the PIVOT ENDCAPS(51) to the PIVOT CUFF BUSHINGS(45) at both sides with ROUND HEAD SCREWS(M5x0.8x15mm)(70). STEP 11 Slide the HANDLEBAR SLEEVE(52) onto the HANDLEBARS(5). Insert the HANDLEBARS(5) onto the ROCKER ARMS(4) and secure with BUTTON HEAD BOLTS(M6x1x16mm)(63), CLAMP WASHERS(M6) (53), and LOCK WASHERS(M6)(75). Slide the HANDLEBAR SLEEVE(52) down to cover the bolts on the HANDLEBARS(5). ASSEMBLY INSTRUCTIONS 11 STEP 12 Install four AA NiMH (Nickel Metal Hydride) rechargeable batteries into the COMPUTER(20). Connect the CONNECTION WIRE(19) and the PULSE SENSOR WIRES(89) to the COMPUTER(20). Slide the COMPUTER(20) onto the bracket on the UPRIGHT(3) and secure with ROUND HEAD SCREWS (M5x0.8x15mm)(70). CAUTION: Be careful not to damage the CONNECTION WIRE(19) and PULSE SENSOR WIRES(89) when attaching the COMPUTER(20). ATTENTION: Use only NiMH (Nickel Metal Hydride) rechargeable batteries with this product. The higher voltage from other types of batteries may damage this equipment. Failure to use NiMH rechargeable batteries will void your warranty and may result in damage to your machine. Stamina is not responsible for non-compliance with correct battery usage. SET UP INSTRUCTIONS LEVELING: MOVING: Equipment Mat Place the Avari GX8 in the area where it will be used. It is recommended that the Avari GX8 be placed on an equipment mat. The maximum usage dimensions of Avari GX8 are approximately 99 1/4" long x 25 5/8" wide x 64 7/8" tall. (These dimensions may vary up to one inch.) An area 4 feet wide x 9 feet long is required for safe operation of the Avari GX8. Make sure that adequate space is available for access to and passage around the Avari GX8. Adjust the STANDS(59) under the MAIN FRAME(1) so that the Avari GX8 sits on the floor without rocking. Refer to the instructions below the illustration. Move the Avari GX8 with the moving wheels on the REAR STABILIZER(2). Lift from the Front Stabilizer of the MAIN FRAME(1). Two people are required to move the Avari GX8. 12 Lift up from the Front Stabilizer for moving. FUNCTION INSPECTION: Visually inspect the Avari GX8 to verify that assembly is as shown in the above illustration. Check the function of the Avari GX8. Stand on the foot pedals and place your hands at a comfortable position on the handlebars. Slowly move your highest foot forward and follow the natural path of the machine. Turn the crank slowly through one complete revolution to verify that the drive train functions properly. Use the "Quick Start" and "+/-" buttons on the COMPUTER(20) to select a program and verify that the Generator System provides different tensions. Refer to the COMPUTER INSTRUCTIONS on pages 17 to 22. Locate and read the WARNING LABEL(95) on the Avari GX8. Make sure that all users read the WARNING LABEL(95). CAUTION: To level the Avari GX8, first screw the STAND(59) located in the middle of the MAIN FRAME(1) all the way up into the MAIN FRAME(1) so that it is not touching the floor. Adjust the four STANDS(59) on each of the four corners, two under REAR STABILIZER(2) and two under the front of the MAIN FRAME(1). When all four are adjusted and the Avari GX8 is stable, tighten the NUTS(3/8"-16)(79) against the MAIN FRAME(1) and REAR STABILIZER(2) to lock the STANDS(59) into position. While you are adjusting these four STANDS(59), the one STAND(59) located in the middle of the MAIN FRAME(1) must not be in contact with the floor. Only after the Avari GX8 has been stabilized with the four STANDS(59) on the corners will you position the middle STAND(59) so it is in contact with the floor to provide extra stability for the MAIN FRAME(1). 13 OPERATIONAL INST...