Assessments - 4, GPA: 4.3
(
)
)
|
Fotos e especificações Vision Fitness X6100 |
Facilidade de uso
Secure the pedal arm to the rotation axle with a washer (8x30x1.5T) and screw (M8x20L). Tighten with a 5mm T-shaped wrench. • Place the pedal arm bracket cover over the bushing housing of the pedal arm. Secure in place with a washer (5x10x1T) and screw (M5x10L). Tighten with the screwdriver. • Repeat both steps on the left side. BLUE BAG • Slide a wavy washer (25x34x2T) onto the right rotation axle. Slide the bushing housing of the right pedal arm onto the right rotation axle. The pedal arm roller wheel should be placed in the groove of the guide rail. Secure the pedal arm to the rotation axle with a washer (8x30x1.5T) and screw (M8x20L). Tighten with a 5mm T-shaped wrench. • Place the pedal arm bracket cover over the bushing housing of the pedal arm. Secure in place with a washer (5x10x1T) and screw (M5x10L). Tighten with the screwdriver. • Repeat both steps on the left side. BLUE BAG Pedal Arm Bracket Cover Rotation Axle 2STEPGuide Rail Pedal Arm 6 7 STEP 3 Console Console Mast Boot Frame Bracket X6100 STEP 3 • With the screwdriver, remove the screws for the water bottle cage in the center of the console mast. Slide the rubber boot onto the console mast. • Unfold the wire harness located in the frame bracket. Wrap the wire tie around the end of the wire harness. Pull the wire tie and wire harness up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the mast to the frame using three lock washers (8x14x1.5T) and three capscrews (M8x60L). Tighten with the 6mm L-Shaped wrench. • Slide the rubber boot down the console mast and snap it in place on top of the side cover. • Remove the four screws from the back of the console. Connect the wire harness to the plug in the back of the console. Connect the heart rate wires from the console mast to the console. Attach the console to the console mast with the four screws. • Attach the water bottle cage with the screwdriver and the screws removed earlier in this step. PINK BAG STEP 4 GREEN BAG • Slide a wavy washer (20x29x1.5T) on the lower link arm axle, which is located under the foot plate. Slide the axle through the bracket located on top of the pedal arm. • Secure the lower link arm to the pedal arm by attaching the pedal support bracket with three screws (M8x13L). Tighten with the 5mm T-shaped wrench. • Repeat this step on opposite side. GREEN BAG • Slide a wavy washer (20x29x1.5T) on the lower link arm axle, which is located under the foot plate. Slide the axle through the bracket located on top of the pedal arm. • Secure the lower link arm to the pedal arm by attaching the pedal support bracket with three screws (M8x13L). Tighten with the 5mm T-shaped wrench. • Repeat this step on opposite side. Lower Link Arm 4STEP 8 STEP 5 Dual-Action Axle Cover Link Arm Covers Dual-Action Arm 9 STEP 5 • On the right side, slide the dualaction axle cover into place on the console mast axle. Slide a wavy washer (25x34x2T) onto the axle. Slide the right dual-action arm on the axle. Fix in place with the washer (8x35x2T) and locknut (M8). Cover with the included nut cap. • Make sure the sleeve is in place in the socket joint of the lower link arm. Connect the lower link arm to the dual action arm with a screw (M8x30L). Attach the washer (8x25x1.5T) and nut (M8) to the end of the screw. Tighten with the 5mm L-Shaped wrench and 13mm wrench. • Position the link arm cover over the joint of the lower link arm and secure the two pieces of the cover together with a panhead screw (M4x15L). Connect the cover to each side of the lower link arm with a washer (5x10x1T) and screw (M5x10L). • Repeat these steps on the left side. BLACK BAG i t a l l starts with a vision 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©200...
Este manual também é adequado para os modelos :Formadores - X6200HRT (1.22 mb)