Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Item #7 201611 or 203104 P/N 211999B 12/02 4 WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF 1. Center alignment slot of middle pole section (5) in a alignment, bounce pole top (4) and middle section (5) together as shown Pole sections should have a 3-1/2" (9 cm) minimum While maintaining Install wheel axle (2) through wheel carriage (19) and install wheels (3) 7. WARNING: TIGHTEN BOLT (11) IN LOCKNUT (13) UNTIL FLUSH A. Fit left handle (47) onto adjustment tube (49) so the bottom of adjustment tube (49) sits on the two small ribs of the handle as shown in figure B. 16. Insert spring (50) into back of locking pin (46) as shown. Spring (50) should rest between two small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (55) into bracket on the adjustment tube (49) as shown. The plastic post of the handle pieces should go through the hole in bottom of trigger (55) and hold it into place as shown. 17. Finish handle assembly by attaching right handle (48) using screws (18) as shown. 18. Attach adjustment tube (49) to lower elevator tubes (41) using bolt (60) spacers (51) and nut (39) as shown. 19. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER. Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull trigger to allow lower adjustment rod to move about mid-way into adjustment tube (49), release the trigger so the lower adjustment rod (52) locks into position midway inside the adjustment tube (49). Attach the lower adjustment rod (52) to elevator bracket (27) using bolt (53) and nut (13) as shown. 20. Fit rim (21) securely into bracket (57) as shown. Install reinforcement bracket (59) onto T bolt (58) as shown. Install spring (30) onto T bolt (58) as shown. Install special nut (40) and washer (38) onto T bolt (58). Tighten nut (40) until flush with end of T bolt (58). WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. 21. Install net clips as shown. (See illustration) (EVEN) WITH LOCKNUT S OUTER EDGE. 22. Install net as shown. (See illustration) 8. Secure base struts (10) to base using bolt (15), washers (12), and 23. WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN nut (16). EMPTY, MAY TIP OVER. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS 9. Install pole mount bracket (27) and reinforcement bracket (56) with PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY carriage bolts (28) as shown. Tighten flange nuts (16) completely. RESULT IN BODILY INJURY. Roll the completed assembly to the desired playing area. Insert the 10. Assemble backboard brackets (29) using spacers (33) bolts (34, 35) and T-strap (14) through the slot on the back of the base as shown. Secure nuts (36, 37) as shown. the unit to ground by twisting the tie down stake (23) into the ground and 11. IMPORTANT! Test fit bolts into holes of backboard brackets(29) and hooking the T-strap (14) onto the tie down stake (23). Fill tank with 33 carefully rock them in a circular motion to ream out paint from holes if gallons of water. necessary. Attach lower elevator tubes (41) to backboard brackets (29) IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in using spacers (42) bolt (43) and nut (39) as shown. sub-freezing climates. 24. Apply the height adjustment and moving label (25) to the front of the 12. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS pole as shown. PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. 25. Lock elevator system into highest position (so the backboard is as high Insert T bolt (58) through Slam Jam bracket (57) as shown. as it will go). Apply 10 ft. height indication sticker (54) to adjustment rod Secure Slam Jam bracket (57) and backboard bracket (29) assemblies (52) directly below arrow on handle as shown. Move elevator system to to backboard. Bend upper halves of backboard brackets (29) to line up the next position and apply the 91/2 ft. sticker. Repeat until all height with holes in backboard and secure with bolts (32) and nuts (16). settings have been labeled. (8-10ft.) Tighten completely. 26. Pull trigger (55). Move elevator system up or down to desired height, 13. Attach upper elevator tubes (44) to backboard brackets (29) using release trigger (55) to lock system into one of the five height settings. spacers (42) bolt (43) and nut (39) as shown. WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. 14. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARRANTY CARD: Please remember to complete your product Support pole on sawhorse. Attach upper and lower elevator tubes (44, registration form either 41) to upper pole section (4) using bolts (60) and nuts (39) as shown. Attach pole cap (22) as shown. on-line at: www.huffysports.com/...