Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex key and your own Phillips screwdriver , and adjustable wrench , rubber mallet . Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of the manual. The number after the parentheses shows the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools for assembly. 2” Silver Screw (48)–13/4” Tek Screw (58)–43#8 x 3/4" Screw (6)–6#8 x 2 1/4" Screw (7)–441/2” Bolt (78)–4HWasher (96)–8nsion 8" Nut (11)–23/8" StarWasher (8)–85/16" StarWasher (9)–45/16" x 2" Bolt (2)–4Extension LegNut (10)–4E3/8" x 1" Bolt (4)–73/8" x 1 3/4" Bolt (3)–13/8" x 2 3/4" Bolt (5)–2#8 x 1" Tek Screw(1)–43/1. Make sure that the power cord is unplugged. With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (55) so that the treadmill is more stable. Do not fully fold the Frame until the treadmill is completely assembled. Attach two Base Pads (81) to the Base (85) with two #8 x 1" Tek Screws (1). 85 55 81 1 1 81 1 6 2. Insert an Extension Leg (97) into the Base (85) as shown. If necessary, use a rubber mallet to fully insert the Extension Leg. Next, hold two Extension Leg Nuts (10) in the bottom of the Extension Leg, and tighten two 5/16" x 2" Bolts (2) with two 5/16" Star Washers (9) into into the top of the Extension Leg. 3. Hold the Right Upright (113) near the Base (85). Insert the Upright Wire Harness (73) into the bottom of the Right Upright and out the top. Attach the Right Upright (113) to the Base (85) with a 3/8" x 1" Bolt (4), a 3/8" x 2 3/4" Bolt (5), and two 3/8" Star Washers (8). Make sure that the Upright Wire Harness (73) is not pinched. Start both Bolts before tightening them. 4. Slide the Right Base Leg Cover (83) over the end of the Right Upright (113). Attach the Right Base Leg Cover with two #8 x 2 1/4" Screws (7) and three #8 x 3/4" Screws (6). Be careful not to overtighten the Screws. 97 85 9 2 2 113 8 5 4 8 85 73 73 3 113 83 6 4 7 10 7 1 85 55 1 81 5 2 97 9 85 6 4 5 111 85 7 81 8 10 1 81 5 2 97 9 85 6 4 5 111 85 7 81 8 10 8. Slide the Left Base Leg Cover (82) over the end of the Left Upright (111). Attach the Left Base Leg Cover with three #8 x 3/4" Screws (6) and two #8 x 2 1/4" Screws (7). Be careful not to overtighten the Screws. With the help of a second person, carefully tip the treadmill down so that the Base (85) is flat on the floor. 9. With the help of a second person, hold the console assembly near the Left Upright (111) and the Right Upright (113). Connect the Upright Wire Harness (73) to the Console Wire (119). See the inset drawing. The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN YOU TURN ON THE POWER. Insert the connectors and excess wire into the Right Upright (113). Insert the front ends of the brackets on the console assembly into the Right Upright (113) and the Left Upright (111). Then, insert the rest of the brackets into the Uprights. Make sure that the Wire Harnesses (73, 119) are not pinched. 6 111 82 85 8 73 113 111 Console Assembly 9 7 73 Front of Bracket 119 119 9 10.Attach the console assembly with four 3/8" x 1" Bolts (4) and four 3/8" Star Washers (8). Start all four Bolts before tightening them. Note: The Left Accessory Tray (105) and the Right Accessory Tray (114) are replaceable. If these parts become dislodged from the Console Base (98), simply press them back in. 11. Identify the Latch Assembly (76). Remove the tie from the end of the tube. Make sure that the sleeve has been slid over the indicated hole and that the Latch Knob (108) is locked into the hole. Pull on the sleeve to make sure that it is locked into place. 12. Raise the Frame (55) to the position shown. Have a second person hold the Frame until this step is completed. Orient the Latch Assembly (76) so that the large barrel and the Latch Knob (108) are in the positions shown. Attach the lower end of the Latch Assembly to the bracket on the Base (85) with a 3/8" x 1 3/4" Bolt (3) and a 3/8" Nut (11). Attach the upper end of the Latch Assembly (76) to the bracket on the Frame (55) with a 3/8" x 1 Bolt (4) and a 3/8" Nut (11). Note: It may be necessary to move the Frame back and forth to align the Latch Assembly with the bracket. Lower the Frame (55) (see HOW TO LOWER THE TREADMILL FOR USE on page 21). 76 11 11 Large Barrel 85 3 55 12 4 108 108 Sleeve HoleTube 76...