Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
It is recommended that you place a protective covering on your floor. You will only need to attach the following items. Verify that the following parts and tools are included: Parts • 1 Rear Foot Tube • 2 Handlebar Set • 1 Seat Post • 1 Seat • 1 Console Mast • 1 Console Mast Boot • 2 Mobile Wheels • 1 Console • 2 AA Batteries • 2 Pedals • 2 Wheel Sleeves • 1 Tension Knob • 2 Handlebar Links • 1 Hardware Pack (contents listed below) E) 13mm Nut Quantity: 2 J) 14mm Washer Quantity: 2 K) 20mm Bolt Quantity: 2 I) 12mm Screw Quantity: 2 A) 20mm Bolt Quantity: 2 D) 15mm Bolt Quantity: 4 F) 45mm Bolt Quantity: 2 Tools (included) • 5mm Allen Wrench/ Phillips Screw Driver • Flat Wrench NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Exercise Bike, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. STEP 4 Connecting the Tension Knob a. Remove the 20mm long bolt (Q) on the back of the tension knob. b. Turn the tension knob to level 15. Connect the tension knob to the bottom of the tension knob cable (Figure A, Step 2). c. Grasp the tension knob and firmly pull the tension knob assembly away from the machine in order to attach to the top of the tension knob cable (Figure B, Step 3). Make sure that the copper cable end is seated properly into the "key hole". d. Insert the tension knob into the rectangular opening on the console mast (Figure C, Step 5). e. Secure the tension knob with the 20mm bolt (C) by using a screw driver (Figure D, Step 6). STEP 1 Attach the Front Foot Wheels a. Insert the wheel sleeves on each side of the front wheel tube. b. Align the holes in the wheel sleeves with the holes in the wheel tube. Insert two 12mm screws (I) and secure with the screwdriver. c. Attach the mobile wheels to the wheel sleeves. Insert two 14mm washers (T) and two 20mm bolts (K) and secure with a screwdriver. STEP 8 Attach the Pedals a. Attach pedal spacer (P), handlebar link, and 30mm washer (O) onto the right pedal. Note: The pedals are labeled on the end of each threaded shaft for reference. b. Tighten the pedal with the flat wrench. c. Repeat for left side. STEP 5 Attaching the Dual-Action Handlebars a. Attach console mast spacer (C) onto the console mast. b. Align the holes of the handlebar and slide it onto the console mast. Attach a 35mm washer (B) and 20mm bolt (A) and secure with a 5mm Allen wrench. Repeat for other side. c. Insert two link arm spacers (H,G) into the lower handlebar bracket. d. Align the holes for the handlebar link and the lower handlebar. Insert a 45mm bolt (F) and secure with a 13mm nut (E) using a flat wrench. Repeat for other side. STEP 6 Attaching the Console a. Open the battery cover on the back of the console, insert two AA batteries into the console and replace the battery cover. b. Connect the cables from the con sole to the console cables running through the console mast, making sure that both ends snap together tight. c. Attach the console to the console mast plate with the 15mm screws (R). Secure using a screwdriver. Note: Screws (R) are located on the back side of the console. STEP 3 Attaching the Console Mast a. Unfold the console cable and the tension knob cable, which is folded into the console mast base. b. Slide the console mast boot onto the bottom of the console mast. c. Slide the tension knob cable and the console cable through the console mast. (Note: The tension knob cable will only pull as far as the rectangular opening in the console mast. The console cable will need to be pulled through the end of the console mast.) To assist in pulling the console cable and tension knob cable through the console mast, there should be a guide wire attached to the top of the console mast. d. Insert the console mast into the base, secure both sides of the mast with four 15mm bolts (D) using the 5mm allen wrench. Slide the console mast boot into place. STEP 7 Attach the Seat a. Remove the three nuts (S) and washers (T) from the bottom of the seat. b. Attach the seat to the seat post with the three nuts (S) and washers (T), securing with the flat wrench. c. Loosen the pop pin by turning it one or two revolutions, then pull the pop pin mechanism to the outward position. d. With the pop pin in the outward position, slide the seat post into the base. e. Release the pop pin and tighten to the proper position. Figure A Figure B Figure C Figure D 6 5 4 3 2 1 CUSTOMER ASSISTANCE CENTER 1 . 8 8 8 . 9 9 3 . 3 1 9 9 o r w w w. h o r i z o n f i t n e s s . com H a r d w a r e (Actual Size) Express 2 0 0 B) 35mm Washer Quantity: 2 G) Linkarm Spacer (Inner) Quantity:2 C) Teflon Washer Quantity: 2 N) 20mm Arc Washer Quantity: 4 O) Pedal Spacer (Outer) Quantity: 2 H) Linkarm Spacer (Outer) Quantity:2 P) Pedal Spacer (Inner) Quantity: 2 L) 90mm Bolt Quantity: 2 M) Acorn Nut Quantity: 2 STEP 2 Attach the Rear Foot Tube and Pads a. Align ...