Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Tool needed for assembly: Phillips screwdriver (not included).Tool needed for assembly: Phillips screwdriver (not included). Water or sand is needed to fill the bases (not included).Water or sand is needed to fill the bases (not included). IMPORTANT!IMPORTANT! Backboard height should be adjusted only by an adult.Backboard height should be adjusted only by an adult. M5726M5726 1. Basketball 2. Football 3. Soccer 4. Baseball 5. Hockey Owner's Manual with Assembly Instructionswith Assembly Instructions Please keep this instruction sheet for future reference,Please keep this instruction sheet for future reference, as it contains important information.as it contains important information. Adult assembly is required.Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included).Tool needed for assembly: Phillips screwdriver (not included). Water or sand is needed to fill the bases (not included).Water or sand is needed to fill the bases (not included). IMPORTANT!IMPORTANT! Backboard height should be adjusted only by an adult.Backboard height should be adjusted only by an adult. M5726M5726 1. Basketball 2. Football 3. Soccer 4. Baseball 5. Hockey ASSEMBLED PARTSASSEMBLED PARTS Rim Backboard 2 Upper Posts 2 Lower Posts 2 Bases 2 Plugs Base Tube 2 Side Tubes Net Tube 2 Post Covers 2 Base Covers Net BOTH SHOWN ACTUAL SIZE Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws. #8 x 3/4” Screw – 36 #10 x 1 1/2” Screw – 2 Label Sheet ASSEMBLED PARTSASSEMBLED PARTS Rim Backboard 2 Upper Posts 2 Lower Posts 2 Bases 2 Plugs Base Tube 2 Side Tubes Net Tube 2 Post Covers 2 Base Covers Net BOTH SHOWN ACTUAL SIZE Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws. #8 x 3/4” Screw – 36 #10 x 1 1/2” Screw – 2 Label Sheet 2 22 This product contains small parts in its unassembled state. Adult assembly is required. CAUTION • Place the bases on a flat surface. • Note the numbers on the bases and on the posts. • Insert and “snap” the post labeled 1 into the base labeled 1 . • Insert and “snap” the post labeled 2 into the base labeled 2 . • Place the net, printed side up, on a flat surface. • Slide the base tube through the sleeve on the bottom of the net. 1 2 3 Printed Side Up ASSEMBLYASSEMBLY Posts 1 2 Bases Base Tube Sleeve IMPORTANT! Position the base assemblies as shown. Note the labels 2 and 1 . • Place the base assemblies onto the ends of the base tube. Base Tube 1 2 This product contains small parts in its unassembled state. Adult assembly is required. CAUTION • Place the bases on a flat surface. • Note the numbers on the bases and on the posts. • Insert and “snap” the post labeled 1 into the base labeled 1 . • Insert and “snap” the post labeled 2 into the base labeled 2 . • Place the net, printed side up, on a flat surface. • Slide the base tube through the sleeve on the bottom of the net. 1 2 3 Printed Side Up ASSEMBLYASSEMBLY Posts 1 2 Bases Base Tube Sleeve IMPORTANT! Position the base assemblies as shown. Note the labels 2 and 1 . • Place the base assemblies onto the ends of the base tube. Base Tube 1 2 3 33 • Lift the side tubes up and set the ends in the notch in each base assembly. Hint:The top of the net will flop forward. • Slide a side tube, straight end first, through the sleeve on each side of the net. Sleeve Side Tube Sleeve Side Tube ASSEMBLYASSEMBLY 4 5 6 • Fit the upper end of the side tubes into the groove in each post. Post Grooves Side Tubes • Note the numbers on the base covers. • Fit the base cover labeled 1 onto the base assembly labeled 1 . Hint:Make sure the net is not under the base cover. • Insert four #8 x 3/4” screws into the base cover and tighten. • Repeat this procedure to attach the other base cover labeled 2 to the base assembly labeled 2 . 7 1Base Covers 2 • Lift the side tubes up and set the ends in the notch in each base assembly. Hint:The top of the net will flop forward. • Slide a side tube, straight end first, through the sleeve on each side of the net. Sleeve Side Tube Sleeve Side Tube ASSEMBLYASSEMBLY 4 5 6 • Fit the upper end of the side tubes into the groove in each post. Post Grooves Side Tubes • Note the numbers on the base covers. • Fit the base cover labeled 1 onto the base assembly labeled 1 . Hint:Make sure the net is not under the base cover. • Insert four #8 x 3/4” screws into the base cover and tighten. • Repeat this procedure to attach the other base cover labeled 2 to the base assembly labeled 2 . 7 1Base Covers 2 4 44 • Fit the net tube through the sleeve in the center of the net. 8 ASSEMBLYASSEMBLY Post Cover Post Cover • Fit a post cover over the end of a side tube and onto a post. • Insert five #8 x 3/4” screws into the post cover and tighten. • Repeat this procedure to attach the other post cover. 9 • Line up the holes in the ends of the net tube with the hole in each side tube. • Insert a #10 x 1 1/2” screw into each side tube and tight...