Log:
Assessments - 3, GPA: 4 ( )

Instruções de Operação Coleman, Modelo 9232C179

Fabricante : Coleman
Arquivo Tamanho: 51.17 kb
Arquivo Nome : 9232C179.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


–Do not set up your tent under trees. –For best results in windy conditions, position the end End Brace Poles of tent into the wind. (Blue Sticker) Part No. 9232B305 –See owners manual for more tips Awning Poles (Green Sticker) Part No. 9232-306 Rainfly Part No. 9232A307 1 1 Layout & Positioning of Tent –Layout and position tent with door facing desired direction. (illus. 1) –Stake down tent, starting with the corners. Do not stretch too tight. Angle the Stakes slightly toward the tent. (illus. 2) Keep the floor taut. Illus. 2 Stake loops properly staked Front Door Roof Sleeve Illus. 1 –Unzip the door WEATHERMASTER™ 17'X9' Instructions apply to Part Number 9232C179 Chain shock-corded POLE ASSEMBLY PARTS Center Curved Roof Poles (Red Sticker) Part No. 9232-302 End Curved Roof Poles (Blue Sticker) Part No. 9232-303 Center Brace Poles (Red Sticker) Part No. 9232B304 2 2 Assemble & Place Forms an arch Roof Poles –Assemble all shock-corded Roof Poles. When assembled will form a continuous arch with both ends pointing down. (illus. 3) –Select Center Roof Poles with Red stickers and square ends. Then insert them through the two center roof sleeves. (illus. 4) –Select End Roof Poles with Blue stickers and round ends. Then insert them through the roof sleeves at each end of the tent. (illus. 4) Shock corded poles Illus. 3 Curved Roof Pole assembly. Pole Sleeves Illus. 4 Curved Roof Pole system shown inserted through pole sleeves. Square end, red sticker poles go into two center pole sleeves. Round end, blue sticker poles go into two end pole sleeves. Tent (illus. 5, 6, 7) –Brace poles illus. 7 Poles should be initially adjusted to the inner most hole “A”. 4 pins at bottom of tent. –Assemble Awning Poles end of Guy Line Rubber Tip. corners (illus. 11) poles (illus. 11) in winds and rain Things You Should Know • Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent. • Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use separate storage bag. • STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE. • TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER DURING STORAGE. • Seam sealer has not been provided with your tent. It is necessary and we recommend seam sealing your tent prior to camping. Seam sealer may be purchased through your local retailer or at your local sporting goods store. 3 Raise Center of –Assemble center shock-corded brace poles (red sticker, longer poles). Pole should be initially adjusted to the inner most hole “A”. (illus. 7) –Insert square end of brace poles into curved roof poles and raise tent upright. should attach to squeeze pins at bottom of tent. Illus 5 illus. 5 Shown with both Center Brace Poles in position and Curved poles through both center pole sleeves. Center Brace Pole Rainfly illus. 6 When attaching the Brace poles to the Curved Poles make sure that the Brace poles naturally point straight down. illus. 9 Tent shown completely set-up. Raise Sides of Tent –Assemble end (blue sticker, round ends) shock-corded Brace Poles –Insert (blue sticker) Brace Poles into end roof assemblies. MAKE SURE when attaching the Brace poles to the curved poles the bottom of the Brace pole naturally points down and toward the center of the tent. (illus. 9) –Brace poles should attach to squeeze –Can be adjusted to accomodate terrain –Tie a loop on the non adjustable –Remove Rubber Tip, insert Awning Poles into plastic “O” ring at end of awning and place loop of Guy Line over pole tips (illus. 10) Replace –Stake out Guy Lines from awning –Drape Rainfly over tent and attach “S” hooks on Rainfly into holes in brace –Awning can be tied down over the tent door for added protection from wind and rain –Awning should be rolled back or tied down Brace Pole Curved poles in pole sleeve Brace Pole with hole for Rainfly “S” hooks Awning illus. 11 Stake out awning poles with adjustable Guy Lines. Slide the metal disc up the rope to tighten Guy Line. Awning Pole illus. 10 illus. 8 Insert Squeeze Pin into pole Plastic “O” Ring • Do not leave your tent set-up for weeks at a time, be aware that exposure to the ultraviolet rays of the sun can seriously damage nylon material and/or cause it to become discolored. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent meets the flammability requirements of CPAI-84. The fabric may burn left in continuous contact with any flame source. The application of any foreign subs...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias