Assessments - , GPA:
(
)
)
Fabricante : Clam Corp
Arquivo Tamanho: 1.73 mb
Arquivo Nome : feb783fd-a342-41c4-9a48-a63fafa3fefb.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
- 8097 p / n 1 0 8 3 2 2 Specifications . Height: 60”(22”packed) . W idth: 45” . Depth: 80”(36”packed) . Weight: 53 lbs. . Instruction p/n 102476 -C l a m C ust o m e r S er vi ce I nf o r m at i o n - NOTICE!! Once used, this shelter cannot be returned to the store. If you have a warranty claim, have your sales receipt ready and contact Clam Corporation Customer Service by email inquiry or direct by calling: . Customer Service Hrs: -9am to 4pm, Mon. . Clam Corporation 600 Clydesdale Trail Medina, MN 55340 . Phone -763-231-4120 . Fax -763-231-4121 . Website – . Email – customerservice@clamcorp.com Fri. Central Standard Time Clam Corporation cannot honor warranty without an original, dated receipt. -P art s Li st --P art s Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 101070 TUBE, PRO CANOPY HOOP 3 101079 TUBE, PRO PORCH HOOP 1 101096 MOLDING, PRO U-CHNL 1 101463 ASSY, GREY PADDED SEAT 1 101466 HAMMOCK, ACCESSORY 1 102495 BASE, PRO 08-09 1 102502 TUBE, PRO SEAT RAIL SUPPORT 1 102433 TENT, 08/09 PRO 1 101042 BRKT, RH CANOPY 1 101043 BRKT, LH CANOPY 1 101069 POLE CANOPY 6 101078 TUBE, PORCH 2 101146 CHANNEL, 8.78 ALUM EXT 2 101420 BRKT, FRONT RETAINER 1 102430 BRKT, REAR RETAINER 1 101652 TUBE, 20.00 SEAT RAIL 2 101048 BLOCK, SLIDE 4 101080 SCREW, 1/4-20 X 1.25 8 101081 WASHER, 1/4 FLAT 10 101082 NUT, 1/4-20 THIN NYLOCK 26 101083 CAP, TUBE SPACER 8 101088 SCREW, 1/4-20 X 0.75 8 101147 SCREW, #10 x 1.00 4 101148 SCREW, #6 X 0.38 16 101429 PLUG, 1.16 DIA TUBE 4 101430 CAP, TUBE 1 X 2 -1/8 2 102512 SPRING, CATCH 1 101486 SCREW, 1/4-20 X 1.75 4 101487 SCREW, 1/4-20 X 2.75 2 101613 SPACER, PLASTIC 4 101614 SCREW, 1/4-20 X 2.50 4 101470 SCREW, 1/4-20 X 0.50 4 102476 MANUAL, 08/09 PRO 1 101095 ROPE, 3/8 DIA X 9 FT 1 101399 SEAT SWIVEL ASSEMBLY 1 2 -P art s Di ag r a m --P art s Di ag r a m - 3 -St e p O n e --St e p O n e - 4 -St e p Tw o --St e p Tw o - 5 -St e p T hr e e --St e p T hr e e - 6 -St ep F o u r --St ep F o u r - 7 -St e p Fi v e --St e p Fi v e - Latch Clip (p/n 102512) Rear Seat Bracket (p/n 102430) 8 -St e p Si x - 1 ” x 2” Rec tan gul ar S upport T u be (p/n 102502) Pro Bas e (p/n 102495) -St e p Si x - 1 ” x 2” Rec tan gul ar S upport T u be (p/n 102502) Pro Bas e (p/n 102495) 9 -St e p S e ve n --St e p S e ve n - 10 11 -St e p Ei ght - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. -St e p Ei ght - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. -St ep N i n e - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Pro Tent (p/n 102433) -St ep N i n e - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Pro Tent (p/n 102433) 12 -St e p T en --St e p T en - Feed the length of the porch hoop pole through the porch hoop sleeve sewn on the Tent. Slide the porch hoop pole onto the porch poles, engaging the second hole position. Attach the porch velcro on each side of the tent. 13 -St e p El e v e n --St e p El e v e n - To “set”the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the molding over the tent material and base lip. Continue pressing outward in both directions until you have secured about twelve inches of molding onto the base. Having temporarily secured the tent to the base, take a walk around the unit. Readjust the molding until you have verified the proper porch hoop pole position and also that the tent sides and corners are properly proportioned. When satisfied, continue applying the molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Use a side cutters to trim the ends of the molding if they are not equal relative to base. If the ends of the molding extend beyond the rear edges of the canopy brackets (check by feeling from outside the Tent), use a side cutters to trim the ends back to 1-2” behind the canopy brackets. Reinstall the rear adjustable spreader pole to tighten the fit of the tent. If everything still looks good, secure the molding with the #6 phillips screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation. 14 -St e p Tw el ve --St e p Tw el ve - Angle the seat assembly slightly while placin...