Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
19
20
21
22
Interface Manager
Card Installation
Push the
ejector
Repeat steps 17 through 19 for each controller to be
handles
installed. Install 6U filler panels (slot covers) into all
Push the ejector handles
inward to
unused slots.
so that they extend
lock the
Caution: Failure to install filler panels in unused
towards the outer edges
controller
slots may result in thermal damage to the
Tighten the captive screws to secure the controllers into
of the Interface Manager
in place.
hardware.
the expansion cage.
card.
23
24
25
26
Align the sides of the Interface
Manager card with the guides
in either one of the 4U slots in
the expansion cage. Gently
push the Interface Manager
card into the expansion cage
slot, making sure that the
alignment pin on the card
aligns with the alignment hole
in the corresponding cage
slot. Push the card until the ejector handles engage the
If necessary, install a 4U filler panel (slot cover) into
metal rails on the top of the cage.
the unused 4U slot.
Note: If this is an upgrade installation, you will
Caution: Failure to install filler panels in
need to remove a 4U filler panel before installing
Push the ejector handles inward to lock the card in
unused slots may result in thermal damage to
Tighten the captive screws to secure the Interface
the Interface Manager card.
place.
the hardware.
Manager card into the expansion cage.
27
28
29
30
Connect the SCSI
connectors on the
Connect each of
FC interface
the connectors
controllers to the SCSI
CASCADE
TO FIBRE CHANNEL CONTROLLERS
NETWORK
SERIAL
AUX
STATUS
from the other end
connectors on the
of the Ethernet
library SCSI
ERROR
cable bundle to
bulkhead. Refer to the
the Ethernet port
HP StorageWorks
on the FC interface
Interface Manager
Connect the FC cables from any external fibre devices
Connect the four connectors from one end of the
controllers.
and Command View TL Installation Guide for detailed
to the FC connectors on the FC interface controllers.
Ethernet cable bundle to the four Ethernet ports labeled
Note: The order in which the four Ethernet ports
SCSI cabling instructions. Secure the SCSI cables going
Route the FC cables through the access port on the
“To Fibre Channel Controllers” on the Interface
labeled “To Fibre Channel Controllers” on the
from the controller to the library bulkhead by snapping
back of the library.
Manager card.
Interface Manager card are connected to the FC
them into the clips in the upper and lower cable clamps
Caution: Do not pinch the FC cables or bend
Note: Be sure to connect all four Ethernet
interface controllers is inconsequential. If less than four
located on the electronics enclosure. To prevent
them in such a way that the radius of the bend
cables from the Ethernet cable bundle, even if
FC interface controllers are installed, leave the unused
interference with the door, do not use the fourth and fifth
is less than two inches.
you are not using four FC interface controllers.
connectors from the Ethernet cable bundle hanging.
clips from the right edge of the cable clamp.
31
32
33
34
CASCADE
NETWORK
SERIA
Power on the ESL9000 Series library using the following
sequence:
a. Turn on both circuit breakers on the AC power
distribution assembly.
CASCADE
TO FIBRE CHANNEL CONTROLLERS
NETWORK
SERIAL
AUX
STATUS
b. Verify that all access panels are closed, all back
CASCADE
TO FIBRE CHANNEL CONTROLLERS
NETWORK
SERIAL
AUX
STATUS
ERROR
panel cable connections are firmly in place, and all
ERROR
doors are closed.
c. Turn on the power switch located below the control
panel.
To prepare for the configuration procedure, use a standard
After successfully installing the hardware, proceed to the
RJ-45 network cable to connect the network port of the PC
Verify that filler panels are installed in all unused slots in
“Configuration” section.
Connect a standard RJ-45 Ethernet cable from the LAN
or laptop to the port labeled "Cascade" on the Interface
the expansion cage. Push the electronics bay back into
to the Ethernet port labeled “Network” on the Interface
Manager card. Route the cable through the access port on
the library cabinet and finger-tighten the two captive
Manager card.
the back of the library (see step 30).
screws to secure the electronics bay in place.
Configuration
Configuration
For detailed configuration instructions, refer to Chapter 3, “Configuration and Software Installation,” of the
HP StorageWorks Interface Manager and Command View TL Installation Guide
(continued)
Starting Command View TL
Getting/Setting the IP Address
b. At the login prompt, use the following information:
of the Interface Manager Card
1.
Install the Command View TL software on the management
• Username: cliadmin
Note: HP recommends using a static IP address
station.
1.
Start a Telnet session on the PC or laptop that you connected
• Password: clipwd
provided by your network administrator for the
to the Interface Manager card in Step 32:
a. Insert the Command View TL software CD into the
2.
To display the current network IP address along with other
Interface Manager card rather than an IP address
CD-ROM drive of the management station.
a. From a command prompt, enter the following:
network information, enter the following command:
assigned by DHCP.
b. If autorun is disabled on the CD-ROM drive, locate and
telnet 192.168.2.1
show network ipaddress
3.
Obtain an IP address, subnet mask, and gateway address for
double-click the setup.exe file on the CD.
Note: The above IP address is the IP address of the
• If the IP address is 1.1.1.1, then DHCP mode was either
the Interface Manager card from your network administrator.
c. Follow the instructions on the screen to complete the
cascade port. It is not the network IP address. The
disabled, or unable to obtain an IP address automatically.
installation.
cascade IP address is hardcoded into the Interface
Proceed to Step 3 to set the IP address.
4.
To change the IP address enter the following command
Manager card and is separate from the network IP
with all arguments: set network ipaddress
• If the IP address is anything other than 1.1.1.1, then
address.
address>
2.
Open a supported browser on either the management station
DHCP obtained the IP address automatically. If you choose
or any computer on the LAN, and enter the following URL in
to keep this IP address, then record it and proceed to
Note: The default gateway must be set to a valid
the address field:
Step 5. To change the address, continue with Step 3.
gateway address.
http://
5.
Use the exit command to end the Telnet session.
management station. If you are opening a browser on the
management station itself, you can substitute localhost for
6.
Disconnect the Ethernet cable from the Cascade port of the
the hostname).
Interface Manager card.
Configuring Command View TL
7.
Using a 5/32 inch Allen wrench, close and secure the back
access door of the library.
After installing the Interface Manager card and Command View TL,
you must perform the following configuration steps using
Command View TL Prerequisites
Command View TL:
© Copyright 2005 Hewlett-Packard Development Company, L.P.
For the server side, Command View TL requires a management
station (server) with a minimum of:
Second Edition (March 2005)
• Set the Command View TL administrative password.
• Pentium III 500-MHz, 256-MB RAM
Part Number: 341428-002
• Verify proxy settings for the management station.
• 10/100 Base-T network card (a static IP address is recommended)
• Add all libraries to Command View TL that will be monitored.
• Microsoft Windows 2000 Professional or Server edition SP3,
Windows XP Professional
• Add the license key for Command View TL and any additional
features that you have purchased.
For the client side, Command View TL requires the following:
• Configure properties for each library.
• Microsoft Internet Explorer v6.0 SP1 or later, or Netscape
*341428-002*
• Configure host access (Secure Manager).
Navigator v6.2 or later. Make sure that Java support is
enabled in the browser
For complete instructions for each of these configuration steps, see
“Initial Configuration Steps” in Chapter 2 of the HP StorageWorks
341428-002
• An Internet connection is recommended to enable Command
Interface Manager and Command View TL User Guide.
View TL to receive firmware and software release information
automatically from the HP support website.