Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
2U Rack Rail Kit for HP Disk
Enclosures Installation
Overview
Tools required
Unpacking the rails
Instructions
This document contains instructions for shelf-mount rack
•
T25 torque driver — to secure the rails to the rack.
Before you begin, make sure you have enough room to
hardware used by a variety of shelf-mount products in
•
work. To unpack and prepare the rails:
square- and round hole racks. The rails are aligned
T15 torque driver — to change out hardware pins
1.
Open the box containing the rails.
within the rack cabinet with location pins and spring
if converting to round hole rack.
Abstract
loaded hooks that latch on the RETMA column. A front
Contains instructions for installing HP rack rails into square
and rear screw are required to fully secure the rail kits
or round hole racks for HP devices.
into the cabinet. The front shipping screw is located in
Important safety information
the chassis bezel ear behind the die cast latch/handle.
This installation is to be performed by qualified
WARNING!
For safety and proper mounting,
individuals who have knowledge of the procedures,
the securing screws provided in the kit must be
precautions, and hazards associated with equipment
used on the front and rear of the RETMA column
containing hazardous electrical circuits.
as documented.
WARNING!
These rails, when installed, form
NOTE:
For more information on preparing the
only a shelf for the device to rest on. The device
2.
Remove the rear thumb screw and hold down
device for installation, see the user guide that
is not attached to the rail by any other means.
brackets from the kit and set aside for later.
ships with the device.
Use extreme caution when pulling the device out
from the rack. Ensure that the rack is level and
stable before working on the rack. Be sure the
leveling jacks (feet) extend to the floor and that
Kit contents
the full weight of the rack rests firmly on the floor;
it can slip and fall, causing damage to the device
•
Two rack shelf mount rails.
or injury. HP is not responsible for any damage
•
Mounting hardware for square holes is pre-installed.
or injury caused by the mishandling of the device.
WARNING!
Ensure that sufficient personnel are
NOTE:
Hardware that is compatible for
on hand to support the product(s) during the
round holes is included with the shelf kit for
installation process. Use of an appropriate lifting
the rack.
device is recommended as an installation aid.
•
Front and rear retaining screws:
WARNING!
Ensure that the rack has anti-tip
measures in place. Such measures may include
floor-bolting, anti-tip feet, ballast, or a combination
of these as specified by the rack manufacturer
1. Thumbscrew
and applicable codes.
2. Hold down bracket
WARNING!
Always load the rack from the
© Copyright 2015 Hewlett-Packard Development Company, L.P.
Printed in the US
bottom up. Load the heaviest items in the rack
first. This makes the rack bottom-heavy and helps
Round hole racks
Square hole racks
prevent it from becoming unstable.
Front screw: 5697-3033
Front screw: 5697-3034
Installation procedures
WARNING!
Do not overload the branch circuit
Rear screws: 577719-001
Rear screws: 577719-002
1.
Position left and right rack rails at the desired 'U'
that provides power to the rack. The total rack
position in the rack adjusting the rails to fit the rack,
load should not exceed 80 percent of the branch
as needed.
circuit rating.
NOTE:
If mounting the device into threaded hole
HP Part Number: 734750-002
or telco racks, please see www.racksolutions.com
See the Important Safety Information document included
NOTE:
Rails are marked L and R with an
Published: January 2015
to purchase mounting hardware.
arrow indicating the direction in which the
Edition: 2
*734750-002*
with the device.
rail should be installed.
CAUTION:
Electrostatic discharge (ESD) can
Front and Rear bottom edge of rails must align with
damage electronic components. Be sure you are
the bottom of EIA boundary in lowermost 'U'.
properly grounded (earthed) before beginning
2.
Use guide pins to align the shelf mount kit to the
any installation procedure.
RETMA column holes.
Page 1
... Este manual também é adequado para os modelos :
dados de dispositivos de processamento - HP D3700 Enclosure (646.33 kb)
dados de dispositivos de processamento - HP D3700 w/25 300GB 6G SAS 15K SFF(2.5in) ENT Smart Carrier HDD 7.5TB Bundle (646.33 kb)
dados de dispositivos de processamento - HP D3700 w/25 1.2TB 6G SAS 10K SFF(2.5in) ENT Smart Carrier HDD 30TB Bundle (646.33 kb)
dados de dispositivos de processamento - HP D3700 w/25 1TB 6G SAS 7.2K SFF(2.5in) Midline Smart Carrier HDD 25TB Bundle (646.33 kb)