Assessments - , GPA:
(
)
)
Fabricante : Hamilton Beach
Arquivo Tamanho: 361.39 kb
Arquivo Nome : 840087000.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
2 Silk Dry iron on the inside of the garment. Steam Range3 Wool Use a press cloth and steam iron on the inside of garment. 4 Polyester Iron while fabric is still damp. 5 Rayon Iron using spray if necessary. 6 Cotton, Linen For cotton, iron while still damp or use spray. For linen, iron fabric on the inside of the garment. For vertical steaming. Optional Features (on selected models) Adjustable Steam Switch This switch provides minimum steam for wool or maximum steam for linen. Set the switch to O to change to Dry Iron or to vertical steam. Spray and Blast of Steam Buttons Push Blast Button for an extra blast of Blast Spray steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Auto Shutoff Reset Button/Light The light comes on when the iron is first plugged in. After one hour, the iron will shut Reset Button off and the light will go out. Push the Reset Button to turn the iron Light back on. Power On Light This light comes on when the iron is plugged in and remains on until the iron is unplugged. The light stays on even if Temperature Control Dial is turned to Off. Power Light Optional Features (continued) Retractable Cord (not available on all models) 1. Press and hold the Cord Release Button while pulling cord to desired length. Do not unwind cord beyond the tape indicator on the cord. Cord Release Button 2. To store cord, place the iron, sole- plate down, on ironing board. Unlatch Retractable Cord Handle and wind clockwise. Wind clockwise IMPORTANT! Do not press Cord Release Button while winding cord. Only wind clockwise or the cord may jam. See illustration. 3. If cord jams while winding, push the Cord Release Button to unwind slightly until cord is free. Then slowly start to wind clockwise again. If Retractable Cord Handle comes off, it is designed to snap back in place. 1. Place pins of handle into slots in reel. See illustration. Retractable Cord Handle 2. Lift handle up until it snaps in place. Quick Storage Shield There is no need to wait for the iron to cool before storing. Make sure the iron has been turned off and unplugged. Then, place the Quick Storage Shield on the iron immediately after ironing. CAUTION: The soleplate may be hot, so care must be used in placing the Quick Storage Shield on the soleplate. Caring for Your Iron Iron 1. The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to Off. Unplug the iron and hold over a sink. Slowly tilt pointed end of iron down over sink. Water will run out of water tank opening. 2. After iron has completely cooled, wrap cord loosely around the iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. Do not immerse in water. 3. Always store iron upright in the heel rest position. Troubleshooting PROBLEM Things TO CHECK Iron won’t heat. • Is the iron plugged in and the outlet working? Check the outlet by plugging in a lamp. • Is the Temperature Control Dial turned to a fabric setting? • If auto shutoff model, is the Reset Light illuminated? If not, push to reset. Water is leaking out of the iron. • Do not overfill the water tank. • If steam ironing, is Adjustable Steam Switch in a steam position that matches the Temperature Control Dial steam range? Did the iron have enough time to preheat? • If dry ironing, make sure the Adjustable Steam Switch is in the DRY IRON position. Iron won’t steam. • Check the water level. • Is the Adjustable Steam Switch in the STEAM position? • Has the iron had enough time to preheat? Iron leaves spots on clothing. • ALWAYS empty the water tank of the iron after using. Water left in the tank may discolor clothing and soleplate. Wrinkles not removed. • Check Temperature Control Dial is set to correct fabric. Iron too hot. • Check Temperature Control Dial and set to lower setting. Let iron cool down 5 minutes before continuing. Cord is twisted. (Non-retractable model only.) • Unplug iron and let cool. Hold iron cord in the middle of entire length. Let plug and iron dangle freely until cord uncoils. This will extend the life of your iron cord. Retractable cord will not unwind. • Rewind a small amount of the cord, then fully depress the Cord Release Button and pull the cord to desired length. Vertical steam is weak or leaks. • Check the water level. • Is the Adjustable Steam Switch in the O position? • Is the Temperature Control Dial at highest setting (6)? • Has the iron had enough time to preheat? Customer Service If you have a claim under this warranty, please call our Customer Service Number. For faster service please have model, series, and type numbers ready for operator to assist you. These numbers can be found on the heel rest of your iron. MODEL: _______________ TYPE: ________________...