Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
SPRAY MIST ® Button 2. Power “ON” Indicator Light 3. Power Cord 4. Heel Rest 5. Large Water Reservoir 6. Fabric/Temperature Dial 7. Soleplate 8. Easy-to-Fill Water Tank 9. Steam Dial 10. Steam Vents . 5 FILLING THE WATER RESERVOIR You must fill the water reservoir with water to use the SPRAY MIST ® feature and to get steam out of your iron. TIP: Sunbeam tests each iron at the factory to ensure that they function correctly. The test may leave a small, harmless amount of water within the water reservoir. Before you fill the water reservoir, please consider the following: . While this iron was designed for use with tap water, very hard water will reduce the performance of the iron. If your water is very hard, Sunbeam recommends that you use tap water the first time, then consider using demineralized or distilled water for subsequent use. You should use tap water once a month, however, to maintain the iron’s optimal steam performance. . Do not use water that has passed through a home water softening system. This type of water contains minerals that will decrease the performance and shorten the life of your iron. Use demineralized or distilled water, instead. IMPORTANT: When not ironing, always set the Steam dial to Dry/O and the Fabric/Temperature dial to Off/O. To fill the water reservoir: 1. Make sure the iron is UNPLUGGED and that the large Fabric/Temperature dial is set to Off/O and the small Steam dial is set to Dry/O. 2. Hold the iron at an angle. 3. Fill the water reservoir with tap water until it reaches the maximum fill level. WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries. DRY IRONING 1. Plug the cord into a 120-Volt AC outlet. 2. Turn the small Steam dial to the Dry/O setting. 3. Turn the large Fabric/Temperature dial to the fabric setting Synthetics). Allow the iron to heat it is sitting on its heel rest on TIP: Refer to the Ironing Guide . 6 STEAM IRONING 1. Follow the instructions for “Filling the Water Reservoir” on Page 6. 2. Plug the cord into a 120-Volt AC outlet. 3. Turn the small Steam dial to the appropriate setting. 4. Turn the large Fabric/Temperature dial to the fabric setting you desire (Synthetic, Silk, Linen, Cotton or Wool). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. TIP: Refer to the Ironing Guide on Page 10 for the recommended setting for your fabric. 5. The Temperature Indicator Light will go off when iron reaches appropriate temperature. HOW TO USE THE SPECIAL FUNCTIONS SPRAY MIST ® The SPRAY MIST ® feature dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases. To use the SPRAY MIST ® feature: Press the SPRAY MIST ® button firmly. AUTO-OFF After 30 minutes, the power indicator light will flash steadily. This indicates that the iron is no longer heating. To restart the iron, unplug the power cord and plug it back in. If you do NOT want to iron any longer, unplug the iron. Then turn the small Steam dial to Dry/O and the large Fabric/Temperature dial to Off/O. WARNING: Auto-Off is a safety feature and is not a recommended means for turning your iron off. See “Caring for Your Iron After Use” on Page 8. . 7 CARING FOR YOUR IRON AFTER USE TURNING OFF YOUR IRON 1Turn the small Steam dial to Dry/O and the large Fabric/Temperature dial to Off/O. 2. Unplug the iron from the power source. WARNING: NEVER yank the power cord when unplugging the iron, this can damage the cord. STORING YOUR IRON 1. Allow the iron to cool. 2. If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, turn the iron upside down to allow water to flow from the fill hole. Shake the iron gently to remove trapped water drops. Close the water reservoir cover. 3. Loosely loop the power cord together and store the iron on its heel rest. IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord. TIP: When not ironing, always set the small Steam dial to Dry/O and the large Fabric/Temperature dial to Off/O. MAINTAINING YOUR IRON CLEANING THE SOLEPLATE Clean the soleplate if starch or other residue accumulate. To clean the Soleplate: 1. Allow the iron to cool and then wipe it with a soft, damp WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar This will damage the finish. 2. Run the iron over an all-cotton cloth to . 8 IRONING TIPS . Always read garment labels and follow the manufacturer’s ironing instructions. . Sort the articles to be ironed according to the type of fabric. . You should first iron garments requiring low temperature (e.g., silks and synthetics) to avoid damaging them with an iron that is too hot. . If you are unsure of the fabric content of the garment, test a small area, such as a seam or facing, before ironing a visible area. Start with a low temperature and gradually increase the heat to f...