Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Fig. 8Intermitente OPERATING INSTRUCTIONS ( CONT.) 6 ATOMIZER SPRAY NOZZLE The atomizer spray nozzle is useful on fabrics with stubborn wrinkles. Press the spray button and a jet of water will spray onto the fabric being ironed. (Fig. 5) The water spray can be used with dry or steam ironing as desired. INSTRUCCIONES PARA OPERAR (CONT.) 17 SELECTING IRON TEMPERATURESAlways read garment labels and follow the manufacturer’s ironing instructions. Refer to the “Ironing Chart” on page 9 for temperature recommendations: • Use low settings for nylon and other synthetics. •• Use moderate settings for wool, silks, and blends. ••• Use high settings for cottons and linens. 1. Stand the iron upright on its heel. 2. Plug the cord into a polarized, 120V AC electrical outlet. 3. Press the electronic temperature control until you get the desired fabric/temperature setting. 4. The light on the right side of the LED display panel will stop flashing when the desired temperature has been reached. (Fig. 6) IRONING HINTSWARNING! To prevent fire, do not leave iron unattended while connected. • Sort articles to be ironed according to the type of fabric. This will reduce the need to adjust the temperature for different types of garments. • If you are not sure of the fiber content of a garment, test fabric by ironing a small area such as a seam or inside hem section before ironing a visible area. Start with a low temperature setting and gradually increase to find the best setting. • When reducing the temperature to iron sensitive fabrics, allow approximately 2 minutes for the iron to cool to the new temperature setting. • Fabrics such as velour, wool, linen and silk are best ironed with an ironing cloth to prevent shine marks. Fig. 5Fig. 6Temp. settings SELECCION DE TEMPERATURA PARA PLANCHARSiempre lea las etiquetas de la ropa y siga las instrucciones de su fabricante para plancharlas. Vea la “Guia para Planchar” en la pagina 22: • Temperatura baja para telas de nylon y otras fibras sinteticas. • • Temperatura mediana para lanas, sedas y mezclas de fibras. • • • Use la graduacion alta para telas de algodon y lino. 1. Asiente la plancha verticalmente sobre su talon. 2. Enchufe el cordon a un tomacorriente polarizado de 120 VCA. 3. Presione el control electronico de temperatura para graduarlo de acuerdo a la tela que va a planchar. 4. La luz en el lado derecho del panel indicador dejarade destellar cuando la plancha llegue a la temperatura seleccionada ( Fig. 6). CONSEJOS PARA PLANCHAR.ADVERTENCIA! Para evitar incendios, no deje la plancha desatendida cuando esteenchufada. • Clasifique las prendas a plancharse de acuerdo al tipo de tela. Esto reducirala necesidad de tener que variar la temperatura para cada prenda. • Si no estasegura del tipo de fibras de la prenda por plancharse, haga una prueba en un area pequena de una costura o parte interior de una basta o dobladillo antes de planchar en un area visible. Comience a planchar con una temperatura baja y aumentela gradualmente hasta encontrar la mejor graduacion. • Cuando reduzca la temperatura para telas delicadas, espere Aprox. 2 minutos para que la temperatura de la plancha baje a la graduacion mas fria. • Las telas como el velur, lana, lino y seda, se planchan mejor con una tela encima para evitar que le queden huellas lustrosas. BOQUILLA ATOMIZADORA DE AGUALa boquilla atomizadorade agua es util para planchar telas con arrugas rebeldes. Presione el boton atomizador para disparar un chorro de agua a la tela que se esteplanchando en seco o al vapor (Fig.5). Grad. deTemp. Fig. 5Fig. 6 OPERATING INSTRUCTIONS ( CONT.) EMPTYING THE IRON 1. Always empty iron after each use. 2. When finished using the iron, turn the variable steam control dial to “0” and press the electronic temperature control button until the power light is lit. 3. Unplug the iron from the electrical outlet. 4. Turn the iron upside down over the sink with the tip pointing downward and allow the water to flow from the opening. 5. Place iron upright and allow to cool before storing. CAUTION! Use caution when emptying the iron. Burns may occur from touching hot metal surfaces, hot water or steam. ELECTRONIC AUTO-OFF The SHARK ELECTRONIC Iron is equipped with an electronic auto-off. The electronic auto- off switches the iron off if it has been left standing unmoved in any position (sideways, flat or upright) for approximately 7-9 minutes. A red light on the LED display panel will flash when the iron switches itself off. (Fig. 7) To switch the iron back on, just shake the iron side- to-side several times. 7 Fig. 7 16 INSTRUCCIONES PARA OPERAR (CONT.) Flash SELF CLEANINGIt is important to “Self Clean” the iron at least every two weeks to remove scale, calcium, etc. The harder the water, the more often the iron should be self cleaned. 1. Set the variable steam control dial to any steam position. 2. Fill the water tank up to the “MAX” level. 3. Stand the iron on its heel. Plug the iron into the electrical outlet. 4. Press the e...