Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
e. thick materials, items with stubborn wrinkles). 5. Preheat the iron until the Indicator Light goes out, usually about 1-2 minutes. This Light will go on and off during ironing to indicate that the temperature chosen by the Temperature Selector Dial is being maintained. 6. Hold the iron horizontally and move the Steam/Dry Selector into the steam position. Steam/Dry Selector is regulated as follows. -6- NOTE: 3 Position Steam/Dry Selector (Right : for High Steam, Center: for Low Steam ) Temperature Zone Steam/Dry Selector Position $—2 Now steam ironing can begin 7. Whenever the iron is positioned vertically, the steaming action will stop. A CAUTION Do not use the Steam/Dry Selector unless the iron is sufficiently hot enough to produce steam, otherwise water will leak out through the vents instead. HOW TO USE AS A DRY IRON 1. Move the Steam/Dry Selector to the Dry position. 2. Position the iron vertically, set the Temperature Selector Dial to " OFF ". 3. Plug in the iron. 4. Set the Temperature Selector Dial to the desired position. (Refer to the FABRIC IRONING CHART in this manual on page 12 ) 5. Preheat the iron until the Indicator Light goes out, usually about 1-2 minutes. HOW TO USE THE "SPRAY" FEATURE Note: Before using the spray feature, check the fabric label for ironing instructions because some fabrics may be spotted or stained with moisture. The spray feature is particularly helpful for removing stubborn wrinkles and where extra dampening is needed. The spray may be used with steam or dry ironing. -7- 1. Simply pump the Spray Mist Button ^ when spray is desired. If the spray doesn't work immediately, keep pumping until it does. 2. To get a finer spray, pump the Button vigorously. To get a more powerful spray, pump the Button more slowly. For best results, use a quick, full stroke. HOW TO USE 'JET OF STEAM "FEATURE The"Jet of Steam"feature provides extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles. The "Jet of Steam" feature operates properly only in the " <££> " indication area of the Temperature Selector Dial when steam or dry ironing (If used at lower setting, water spotting will occur because the iron is not hot enough to change water to steam ). If you have not used the " Jet of Steam " feature for a long time, it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed. Simply test the " Jet of Steam " feature several times away from the ironing board and clothes to be ironed. This will prevent brown spotting or water spotting on the clothes. 1. Fill the iron as described in "HOW TO FILL WITH WATER 2. Position the iron vertically and be sure the Temperature Selector Dial is set to "OFF ". Plug the AC Power Cord into the electrical outlet. 3. Set the Temperature Selector Dial to the 11 & " indication area 4. Preheat the iron until the Indicator Light goes out, usually about 1-2 minutes. 5. Simply pump the " Jet of Steam Button " when steam is desired. Pump the " Jet of Steam Button " several times at the beginning of each ironing session. 6. Allow at least 2-5 seconds between uses of "Jet of Steam Button " to prevent water spotting. Use a press cloth if necessary. A CAUTION“ Do not use "Jet of Steam Button " until the Thermostat Operating Indicator Light turns off after setting the Temperature Setting Dial to " 6", otherwise hot water may leak from the Soleplate and burns may result, and it may become the cause of corrosion. HOW TO USE "VERTICAL STEAM" FEATURE To get better results when using vertical steam, hang the garment on a clothes hanger. Curtains and drapes may also be steamed once they're hung. Hold the iron away from your body, close to but not touching the fabric. Pull the fabric tight with your free hand and pump the Vertical Steam Button (Jet of Steam Button) at 2-5 seconds intervals as you pass the iron over the wrinkled fabric. AWARNING ■ Never iron clothes on the body or point your iron at anyone when steaming. ■ Keep hands and body away from steam areas while using vertical steam feature. SELF-CLEANING With the self-cleaning feature you can flush out mineral residue from the steam generating chamber and the steam vents, refreshing your iron each time for a longer steaming life. It is very important to operate the self-cleaning feature after each steam ironing to prevent mineral accumulations from hardening. 1. Check water level. Water level should be at 1/2 full mark. When water level is less than half full, fill with water according to the instructions in "HOW TO FILL WITH WATER". 2. Preheat at" 6" setting (for about 1-2 minutes). Make sure that the Steam/Dry Selector is in the Dry position. 3. Set the Dial to " OFF" and remove the AC plug. 4. Hold the iron horizontally over the sink. 5. Pump the "Jet of Steam Button " quickly (at least 3 times per second) about 20-30 times. 6. While self-cleaning, tilt the iron up and down slowly t...