Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Note: Empty the Calc Clean tank if there is water in it. See chapter ‘Auto Calc Clean function’. 3 Slide the carry lock slide to the left to unlock the iron. 4 Take the iron and the heat-resistant iron resting mat off the steam generator. 5 Place the heat-resistant iron resting mat on the ironing board and put the iron on it. Note: You can safely put the hot iron on the mat during ironing MIN MAX English EnGlish 6 To iron with steam, set the temperature dial to 2 or higher. Put the plug in an earthed wall socket. Set the on/off knob to ‘on’. The steam light flashes to indicate that the steam generator is heating up. After 2 minutes the appliance is ready for use.You hear two beeps, the steam light stops flashing and stays on. Press the steam trigger for steam. Type GC9040 only:To remove stubborn creases, you can use the steam boost function. Set the temperature dial between 3and MAX. Press the steam boost button. Never direct the steam at people. Press the steam button to select the desired steam setting. ;for moderate steam output and # for high steam output (set a temperature from 3 to MAX) lfor low steam output (set a temperature from 2 to MAX). Note: If you do not use the iron for more than 10 minutes, the appliance switches off automatically for safety reasons.The automatic shut-off lightflashes.To switch on the appliance again, press any button. This appliance is equipped with an Auto Calc Clean function. Over -- - - - OFFONOFFONONONOFFONOFFON 7 8 Auto Calc Clean function time, scale particles build up inside the steam generator.The appliance automatically performs a Calc Clean process to clean itself from scale after using 6 to 8 tanks of water. 10 EnGlish 1 When the Auto Calc Clean process takes place, the Auto Calc Clean light flashes and you hear short beeps. Wait approximately 2 minutes for the appliance to complete the process. During this process, the appliance occasionally produces pumping and clicking sounds. When the Auto Calc Clean process is completed, the Auto Calc Clean light goes off. The Calc Clean tank light flashes. - - , OFFOFF Press the Calc Clean tank emptying button and empty the Calc Clean Refill the water tank and reattach it to the steam generator. The Auto Calc Clean process is now finished and you can start ironing when the steam light is on continuously. Note: If you do not empty the Calc Clean tank, the tank will overflow during The Auto Calc Clean system keeps the appliance sufficiently clean. Remove the water tank. tank into the sink. the next Auto Calc Clean process. Manual Calc Clean process - - Hovewer, you can also perform the Calc Clean process manually for additional cleaning. 1 Fill the water tank to the maximum level. MINMAXMINMAX EnGlish 11 Put the mains plug in an earthed wall socket. 12OFFON12OFFON To start the Calc Clean process manually, keep the middle steam selection button pressed while switching on the appliance at thesame time. Release the steam selection button only when the blue Auto Calc Clean light flashes. Follow steps 1- of the Auto Calc Clean process described above. Note:The manual Calc Clean process can only be activated if the appliance issufficiently cold. If the appliance is too hot for the manual Calc Clean process, the steam selection button flashes and the appliance continues to heat up for use. storage 1 Switch off the appliance (1) and unplug it ( ). -Press the cord rewind button to store the cord. -Empty the Calc Clean tank if it is filled. Wind the supply hose round the bottom of the steam generator. Note: Make sure the supply hose sits properly in the storage groove and inside the bracket. Place the heat-resistant iron resting mat on the steam generator and put the iron on the mat. Note:You do not have to wait for the appliance to cool down.You can store the appliance immediately after use. 1 EnGlish Slide the carry lock slide to the right to lock the iron onto the steam generator. 5 With one hand, you can now easily carry the whole appliance by the handle of the iron. Troubleshooting This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, please contact the Philips Consumer Care Centre in your countr y. Problem Possible cause and solution The appliance does not become hot. There is a connection problem. Check the mains cord, the plug and the wall socket. The appliance has not been switched on. Set the on/off knob to ‘on’. The set temperature is too low. Set a higher temperature. Smoke comes out of my new ironing system when I switch it on. Some par ts of the appliance have been lightly greased in the factor y and may initially give off some smoke when heated.This phenomenon is perfectly normal and ceases after a shor t while The appliance does not produce any steam. There is not enough water in the water tank. Fill the water tank. The steam generator has not heated up sufficiently. Wait approx. 2 minutes. The set ironing temperature i...
Este manual também é adequado para os modelos :Irons - GC9020/02 (4.57 mb)