Assessments - 0, GPA: 0 ( )

Fabricante : Philips Arquivo Tamanho: 8.95 mb Arquivo Nome : Língua de Ensino:

Note: For the best results, we advise you to use the ‘OptimalTemp’ mode. 1 2 Press the ECO button when the appliance is switched on.The Smart light starts flashing green.When the iron has reached the ECO modeand is ready for use, the Smart light stops flashing and lights up green continuously. To go back to the ‘OptimalTemp’ mode, press the ECO button again. ironing tips Minimising wrinkles while drying Star t wrinkle removal early in the dr ying process by spreading out your laundr y properly after washing and by putting garments on hangers to make them dr y naturally with fewer wrinkles. Best practice shirt ironing Star t with the time-consuming par ts like collar, cuff links and sleeves. Next, iron the bigger par ts like front and back to prevent wrinkling the bigger par ts when you are busy ironing the time-consuming par ts. Collar: When you iron a collar, star t on its underside and work from the outside (the pointy end) inwards.Turn over and repeat. Fold down the collar and press the edge for a more crisp finish. Buttons: Iron on the reverse side of the buttons for more effective and faster ironing. Safety Auto-off -To save energy, the appliance switches off automatically when it has not been moved for 3 minutes in horizontal position, or 8 minutes when left standing on its heel. The Smar t light star ts flashing slowly. -To reactivate the iron, press the steam trigger.The iron star ts heating up again. Note:The steam iron is not switched off completely when it is in Safety Auto-off mode. Unplug the iron to switch it off. Cleaning and maintenance 1 2 Clean the appliance with a moist cloth after every use. To easily and effectively remove stains, let the appliance heat up and move the soleplate over a moist cloth. Tip: Clean the soleplate regularly to ensure smooth gliding. 14 EnGlish storage 1 Remove the plug from the wall socket. 2 Empty the water tank and let the iron cool down in a safe place. 3 Wind the mains cord round the heel of the appliance and fix it with the cord clip. Store the iron on its heel in a safe and dry place. Troubleshooting This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit for a list of frequently asked questions or contact the Consumer Care Centre in your countr y. EnGlish 15 Problem Possible cause Solution The iron is plugged in, but the soleplate is cold. There is a connection problem. Check the mains cord, the plug and the wall socket. The iron does not produce any steam. There is not enough water in the water tank. Fill the water tank (see chapter ‘Using the appliance’, section ‘Filling the water tank’). The iron is not hot enough to produce steam. Wait until the Smar t light has stopped flashing and lights up continuously. You did not move the iron. This iron is equipped with a motion sensor and star ts producing steam as soon as it is moved. The iron is not plugged in. Plug in the iron to switch it on. The iron does not produce any steam when moved. Although the Auto Steam Sensor technology covers a large number of ironing movements, there may still be some movements that do not activate the sensor. Press the steam trigger to star t steaming. The iron continues to steam when it is not moved. Because of the Auto Steam Sensor Technology, steam may continue to be produced for 1-4 seconds to ensure good wrinkle removal at the end of the ironing stroke.This is normal. If you want to avoid this, place the iron on its heel. The iron does not produce Steam Boost. You have used the Steam Boost function too often within a ver y shor t period. Continue ironing in horizontal position and wait a while before you use the Steam Boost function again. The iron is not hot enough. Wait until the Smar t light has stopped flashing and lights up continuously. Water droplets drip onto the fabric during ironing. You have not closed the cap of the filling opening properly. Press the cap until you hear a click. You have put a chemical in the water tank. Rinse the water tank and do not put any perfume or any chemical in the water tank. The Smar t light flashes slowly. The Safety Auto-off mode is active. The iron has been switched to standby mode(see chapter ‘Safety Auto-off ’). To reactivate the iron, press the steam trigger.The iron star ts heating up again. Dir ty water and impurities come out of the soleplate or the soleplate is dir ty. Impurities or chemicals present in the water have deposited in the steam vents or on the soleplate. Clean the soleplate with a damp cloth. 16 EnGlish Problem Possible cause Solution The iron leaves a shine or an imprint on the garment. The surface to be ironed was uneven, for instance because you ironed over a seam or a fold in the garment. The iron is safe to use on all garments. The shine or imprint is not permanent and disappears when you wash the garment. Avoid ironing over seams or folds.You can also place a cotton cloth ove...

Baixe o seu

Para fazer o download, introduza 2 dígitos :