Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• Synthetic fibres Low temperature. •• Silk - wool Medium temperature ••• Cotton - Linen High temperature. FILLING THE WATER TANK Set the steam regulator (5) to the “0” position (Fig. 3) and unplug the iron from the wall socket. Only use clean tap water, without any type of additive. Any other type of liquid could damage the appliance. To obtain better and longer steam production mix tap water with distilled water in the measures shown in the table below. Amount of disti- Water hardness lled water per tap water Ver y soft / Soft 0 Average 0 Hard approx 1 Ver y hard approx 2 Your water supply company can provide you with the hardness levels for your area. Do not fill beyond the maximum water level. This appliance is equipped with a permanent anti-scale system on the inside of the tank, which protects and extends the iron’s useful life. IRONING WITHOUT STEAM Set the steam regulator (5) to the “0” position (Fig. 3) and slide the temperature control (8) to the desired position. The Spray and Super steam functions may be used if required. IRONING WITH STEAM Unplug the iron from the mains supply. Turn the steam selector (5) to the “0” position (Fig. 3) open the lid on the filling spout (4) and fill the tank (2) with water (Fig. 1). Plug the iron into the mains supply and select a suitable temperature. The pilot lamp (9) will stay lit while the iron is heating up and go out as soon as it has reached the selected temperature. As soon as the iron is hot turn the steam selector (5) to the ( ) position (Fig.4) When ironing with steam, make sure that the temperature control (8) is always between the •• and Max settings. When using the steam iron for the first time, tr y it away from the clothes just in case there is any dirt in the steam chamber. When you have finished ironing, set the steam selector (5) to the “0” position (Fig 3) and empt y the tank (2). SPRAY (fig. 6). You can get an additional burst of Spray, whether ironing dr y or with steam, in the following way: - Press the Spray button (6) . Do not use the spray for ironing silk as this may leave water marks. IRONING WITH SUPERSTEAM (fig. 7) Just as with the Spray function you can also get an additional burst of steam when ironing with or without steam by doing the following: - Set the temperature control (8) between the •• and Max settings and wait until the iron reaches temperature. - Raise the iron slightly up off the material and press the super steam button (7) down firmly. - Pause for at least 5 seconds bet ween each jet of steam. SELF-CLEANING CAUTION ! Do this operation over a sink. To keep steam production constant occasional cleaning is recommended as limescale can build up inside the steam ducts and steam chamber. To do this fill the water tank (2), setting the temperature regulator (8) to the “MA X” position. Plug the appliance in and when the lamp (9) goes out press the steam control (5) down to the “Self-clean” position (Fig. 5). Keep the button held down until water stops coming out through the steam holes. As soon as you release the steam control (5) it will automatically go back to the “Max” position (Fig.4) CREASE REMOVAL IN VERTICAL - Set the temperature control (8) between the •• and Max settings and wait until the iron reaches temperature. - Hang the garment on a hanger and place the iron some 10-20 cm away. Never iron a garment if somebody is wearing it at the time (Fig. 8). - Press the super steam push button (7) pausing for at least 5 seconds between each press. ANTI-DRIP SYSTEM This iron is equipped with an anti-drip safety system which automatically cuts off steam production whenever the selected temperature setting is too low. EMPTYING OUT THE WATER TANK Take the plug out of the mains socket, open the lid on the filling spout and empty out the tank by holding the iron pointed-end down and shaking it gently. STORAGE It is advisable to store the iron in the upright position with the water tank empt y and the steam regulator set to “0”. CLEANING & MAINTENANCE Avoid scratching the iron; do not pass it over hard surfaces. Traces of starch or sprays can be removed from the base by using damp cotton wool or a non abrasive cleaning product. Do not put chemicals or detergents into the water tank. The outside surfaces can be cleaned down with a damp cloth, without ever having to use abrasive agents or solvents. REPAIRS Should the cable and /or the appliance become defective do not hesitate in taking it to an Authorised Technical Ser vice Centre. ADVICE ON DISPOSAL: Our goods come in optimised pac kaging. This basically consists in using non-contaminating materials which should be handed over to the local waste disposal ser vice as secondar y raw materials. This product complies with EU Directive 2002/96/CE. The crossed wheelie bin symbol shown on the appliance indi cates that when it comes to dispose of the product it must not be included in with household refuse. It must be taken to a special refuse collection point for electric and electroni...
Este manual também é adequado para os modelos :Irons - PV1412/01 (1.19 mb)