Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
it is advisable to use the normal energy setting only for thick and very wrinkled fabrics. (*) in comparison to the maximum setting. Note: If you work with the “Energy saving” function, the variable steam regulation andtemperature regulation can still be used asrecommended. autoshut-off (model dependent) if during ironing, the steam release button (13-14*) on the iron handle is not pressed for a certain length of time (8 minutes), the steam station will automatically switch off. The “auto shut-off” pilot lamp (4) will flash when auto shut-off has been activated. To switch the steam station back on, press the steam release button again. 4Fabricprotectionsoleplatecover (model dependent) The fabric-protection soleplate cover (17*) isused for steam-ironing delicate garments atmaximum temperature without damaging them. Use of the soleplate cover also does away withthe need for a cloth to prevent shine on darkmaterials. it is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the soleplate cover to the iron, place the tip of the iron into the end of the soleplatecover and pull the elastic strap over the lowerrear of the iron until it fits tightly. To release the soleplate cover, pull the elastic strap and remove the iron. The fabric-protection soleplate cover may bepurchased from our customer service or from ourwebsite. accessory code (after-sales) name of accessory (online shop) 571510 TDZ2045 ENGlISH (button) B O S C H 17 5Calc’n’Clean6rinsingtheironsteamchamber5Calc’n’Clean6rinsingtheironsteamchamber ENGlISH Cleaning the Boiler To extend the life of your steam generator and to avoid any build up of scale, it is essential that you rinse out the boiler after several hours of use (approximately after 50 hours). if the water is hard, increase the frequency. Do not use descaling agents for rinsing out the boiler, as they could damage it. 1.Check carefully that the appliance is cold and unplugged for more than 2 hours, and that thewater tank (1) is empty. 2.place your appliance on the edge of your kitchen sink. 3.remove the plastic cover located on the bottom of the appliance by turning it to theposition. 4.Unscrew the boiler drainage plug using a coin. 5.Holding your steam generator in upside down position, and using a jug, fill the boiler (in thebase unit) with 1/4 litre of water. 6.Shake the base unit for a few moments and then empty it completely over a sink or bucket. To obtain the best result, we recommend that this operation is done twice. Important: before re-closing, make sure no water remains in the boiler. 7.replace and tighten up the boiler drainage plug with a coin. 8.insert and close the plastic cover by turning it to the position. automaticcleanwarning (model dependent) pilot light (6) will flash indicating that boiler must be rinsed. To reset the “Calc’n’Clean” counter, switch the steam station off twice, keeping it off forat least 30 seconds each time. (on > 30s off > on > 30s off > on) Caution! risk of burns! This procedure helps to remove scale particles out of the steam chamber. This cleaning procedure may be performed occasionally (approximately once a year), when after a long period of use with very hard water, scale particles start to come out of the soleplate. 1. Ensure that the iron is cooled down. 2. Set the temperature selector (12) of the iron tothe “min” position. 3. Fill the tank with tap water. 4. plug in the mains cable and set the main power button (7) to the “i” position (illuminated in red). 5. Wait until the “steam ready” indicator lamp (4) lights up. 6. if the steam station has steam control (5*), set it to the maximum position . 7. Hold the iron over the sink or a container to collect the water. 8. press the steam release button (13) and gently shake the iron. Boiling water and steam willcome out, carrying scale and or deposits thatmight be there. This could take approximately 5 minutes. 9. Set the temperature selector (12) of the ironto the “max” position, without pressing thesteam release button (13-14*). The water in the steam chamber will start evaporating. Wait until all the water inside the chamber has been evaporated. 10.To clean the soleplate, immediately rub off any residue by running the hot iron over dry cottoncloth. 18 (button) B O S C H Cleaning& maintenance8adviceondisposalCleaning& maintenance8adviceondisposal attention! risk of burns! always unplug the appliance from the mainssupply before carrying out any cleaning ormaintenance operation on it. 1.after ironing, pull out the plug and allow the appliance to cool down before cleaning. 2.Wipe the housing, handle and iron body with a damp cotton cloth. 3.if the soleplate is soiled with dirt or scale, clean it with a damp cotton cloth. 4. if the cloth is synthetic, it may melt due to the high temperature on the soleplate (16). Switch off the steam and rub off any residue immediately with a thickly folded, dry cottoncloth. 5.never use abrasive products or solvents. ...
Este manual também é adequado para os modelos :Irons - TDS372411E/01 (2.32 mb)
Irons - TDS372810T/01 (2.32 mb)
Irons - TDS373110P/01 (2.32 mb)
Irons - TDS373110P/02 (2.32 mb)