Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• Set the temperature control (15) to the corresponding position by lining it up with the temperature index (14) on the iron: • Synthetics •• Silk-Wool ••• Cotton-Linen • Sort your garments based on their care labels, always starting with clothes that have to be ironed at the lowest temperature. • If you are unsure what type of material the garment is made from, start ironing on the lowest temperature setting and increase accordingly. If the garment is made from mixed fabrics, set the temperature for the most delicate material. • For silk, woollen or synthetic materials iron the reverse side of the fabric to prevent shiny patches. Avoid using the spray function to prevent stains. Setting the steam amount (3) Your iron is equipped with a steam setting selection button (4) and with indicator lamps (5) showing the steam setting, according to the table below: Steam setting eco max steam off Indicator lamps Green Red Off Steam can be generated by gripping the handle (1), or by pressing the steam activation button (2). If the “eco” steam mode is selected, the energy consumption of the appliance will be reduced by means of reduction of electricity and water consumption. A good ironing result can be obtained on this setting for most garments. The steam setting can be changed by pressing the steam setting selection button (4). The iron runs through the following cycle: eco max steam off sensorSteam The “sensorSteam” function automatically switches off the iron when the handle is no longer gripped, thus increasing safety and energy saving. When plugging the iron in, during the irst minute: • The soleplate (13) heats up to the temperature corresponding to the selected setting. • The steam generation is blocked. • The green lamp (5) lashes. enen After the initial 1 minute period: • “eco” setting is automatically selected. • The green lamp (5) stops lashing. • The “activeControl Plus” indicator lamp (3) (clear light) goes on and starts lashing. From this moment on, when the handle (1) of the iron is gripped or if the steam activation button (2) is pressed at steam setting: • The “activeControl Plus” indicator lamp (3) stops lashing. • The pump starts working and steam is generated automatically. If the handle (1) is released: • Steam generation will stop. • The “activeControl Plus” indicator lamp (3) will lash • The iron shuts off automatically. If the handle is gripped again, the iron turns on. If the iron remains plugged in and is not used for several minutes: • After the handle (1) is touched or the steam activation button (2) is pushed again, the green light starts lashing. • Steam generation will not be possible for several seconds, until the appropriate working temperature has been reached. Ironing with steam (4) The steam control is used to adjust the amount of steam produced when ironing (see “setting the steam amount” section). Steam can be generated in two ways : 1. Continuous steam generation : • Set the steam control to “eco” or “max” position. • Grip the handle (1). 2. Steam on demand : • Set the steam control to the “ ” position, to cancel continuous steam generation while gripping the handle (1). On this setting, steam can only be produced when manually pressing the steam activation button (2) under the handle. • Press the steam activation button (2). Important : • Steam is only available if the temperature control (15) is set at the steam symbols - between “••” and “max”. • Adjust the temperature setting and then set the steam control according to the table below. Steam will automatically be produced: Temperature control (15) setting Steam setting •• eco ••• to “max” max Note: Once a steam ironing setting has been chosen using the temperature control (15), steam generation may be delayed for several seconds until the appropriate working temperature has been reached. Ironing without steam (5) This enables the iron to be used for dry ironing. • Grip the handle (1) and set the steam control to the setting. • The temperature control (15) adjusts the temperature of the soleplate (13). Set it to the corresponding position by lining it up with the temperature index (14) on the iron. Select an appropriate temperature for the type of material being ironed (see “setting the temperature” section). • While ironing, do not press the steam activation button (2). Spray (6) This can be used to remove stubborn wrinkles. • Do not use the spray function with silk as staining may occur. • When ironing, press the spray button (7) and water will spray out of the spray nozzle (10) onto the garment. Shot of steam (7) This can be used to remove stubborn wrinkles or to press in a sharp crease or pleat. It cannot be used on a synthetic setting for delicate items. • Set the temperature control (15) to the “•••” or “max” position. • Set the steam control to the “max” position. • Press the shot of steam button (6) on the handle repeatedly at intervals of 5 seconds. Vertical steaming (8) This can be used to remove creases from hanging...