Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
(see fig. 1) • Place the iron horizontally and open the Water Filling Inlet Cover (6). Pour water into the water filling inlet (6) to a maximum of approximately 8 oz. (230ml). Use the water bottle with the spout for this purpose. (see fig. 2) • Close the water filling inlet cover (6). Fig. 2 Fig. 1Cordless PositionTo Iron WithoutA Cord IRONING WITH STEAM • Make sure iron is unplugged from power source. • Set the variable steam control to ‘0’ . • Fill the iron with water following the instructions for filling. • Plug the cord into a 120 Volt AC electrical outlet. • Set the temperature control dial within the steam area i.e. ‘•••’. • Make sure that the iron has reached the selected temperature with the variable steam control set at ‘0’ . IMPORTANT: Do not open the steam control until the thermostat light goes off to indicate that the selected temperature within the steam range has been reached. If you move thevariable steam control up from ‘0’ before the correct temperature is reached, the ironwill drip water. • The variable steam control offers a few different settings: PLEASE NOTE: For maximum steam the temperature control dial should be set at ••• . The temperature control should be set at the beginning only for verydelicate fabrics requiring very gentle steam (setting •). • Steam is produced as soon as the is held in a horizontal position. • Steam will stop coming out when the iron is put on its heel in a vertical position or byturning the steam control ‘0’ . SETTING THE TEMPERATURE • Place the iron on the stand. (Fig. 3) • Insert the plug into the wall outlet. • Set the appropriate ironing temperature indicated in the ironing instructions or in the fabric table by means of the temperature dial (1). (Fig. 4) • Thermostat light (7) will now come on. (Fig. 5) • When the thermostat light (7) has gone out and has come on again you can start ironing. • The thermostat light (7) will come on from time to time during corded ironing. • If you set the temperature control (1) to a lower setting afterironing at a high temperature, do not recommence ironing before the thermostat light (7) has come onand then has gone out again. Fig. 3 Fig. 4Fig. 5RED LIGHT WILL ILLUMINATE CORDED IRONING • Set the 3-position switch (13) to position 13C. (Fig. 6) • Take the iron with the power unit ( 11) from the stand. (Fig. 7) • Either place iron on heel rest or on the stand (12) when you interrupt ironing. CORDLESS IRONING • Set the 3-position switch (13) to position 13B. (Fig. 8) • Take the iron without the power base (11) from the stand. (Fig. 9) • Always place the iron on the stand (12) when you interrupt ironing. • For optimal ironing performance, the iron should be replaced tothe stand for heating up to the set temperature. As soon as the soleplate has regained the set temperature, the thermostat light (7) will gooff. • When cordless steam ironing for a considerable amount of time, the soleplate might cool down more than required. For that reason, we advise you to always use the iron mode if you intend tosteam iron for a considerable time. Fig. 9 Fig. 8 Fig. 7 Fig. 6 WATER SPRAY • Use the spray button to add moisture to stubborn wrinkles. • First make sure that there is water in the tank. • Press the spray button (3) slowly to get a jet spray. (Fig. 10) • Press the spray button strongly and quickly to get a mist. • Please note: If spray does not come out when you press the spray button, cover the spray opening with your finger and press a few times. IRONING WITH STEAM • As indicated on the temperature control dial (1) and the fabrictable, steam ironing is only possible at the higher ironing temperature settings: •• for moderate or ••• for maximum steam. • With conventional steam irons, water may leak from the soleplate if too low a temperature has been selected. However, your new steam iron has an “Anti- Drip” feature which will automatically stop the iron from steaming at too low a temperature. When this happens, you will hear a “Click”. Set the temperature control dial (1) to the advised position. Steaming will restart when the appropriate temperature has been reached. • Ensure that there is enough water in the water reservoir. • Place the iron on its stand (12) and set the temperature control dial (1) to the required position within the “steam area” (•• for moderate or ••• for maximum steam) . (Fig. 11) • After the thermostat light (7) has gone out and has come on again, you may start ironing. • Slide the variable steam control (2) to the required position. (Fig. 12) Fig. 10 Fig. 11 Fig. 12 • Always empty iron after each usage. • After using the iron, turn the variable steam control to ‘0’ and the temperature control dial to ‘minimum’ . • Unplug the iron from the power source. • Set variable steam control to ‘MAX’ . • Open the water inlet cover and turn the iron up-side down over the sink with the tip pointing downward and allow the water to flow from the opening. • Set variable steam control to ‘0’ . • Allow iron to cool on ...