Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• To protect against a risk of electric shock, do not immerse the iron in water or other liquids. • The iron should always be turned to Minimum (Min) before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. • Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. • Always disconnect iron from electrical outlet when filling iron with water, emptying iron or when not in use. • Do not operate iron with a damaged cord or if the iron has been dropped or damaged.To avoid the risk of electric shock, do not disassemble the iron, ship it to the nearest authorized Rowenta Appliance Service Center for examination and repair. Incorrect reassembly can cause a risk of electric shock whenthe iron is used. • Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in or on an ironing board. • Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down there may be hot water in the reservoir. • The use of accessory attachments is not recommended by Rowenta Appliance Company and may result infire, electric shock or personal injury. SPECIAL INSTRUCTIONS 1.This is either a 1500 / 1600 watt appliance. To avoid an overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. Cords rated for less amperage may overheat. Care should be taken to arrange the cordso that it cannot be pulled or tripped over. 3. Your Rowenta appliance is intended for householdor professional use. SAVE THESE INSTRUCTIONS Before Use Helpful Hints -Please read all of the Instructions for Use and the Important Safety Guards carefully. - Remove all packaging from the iron. - Remove the soleplate protector. -It is normal for a small amount of smoke and a light odor to be produced the first time it is used. This will quickly disappear. -Particles may emit from iron during first use. They are not harmful and sould disppear after the iron has been alowed. -When ironing, start with fabrics that require a low temperature setting (•) and finish with those which need the highest temperature (•••). -Mixed fiber fabrics should be ironed on the temperature for the most delicate fabrics. For example a shirt that is 60 % cotton and 40 % polyester should be ironed at the (•) setting for synthetics. -If spray starch is used, spray it onto the reverse side of the garment. Allow starch to penetrate before ironing by setting garment aside for 30 seconds. -For best results, use a mesh type ironing board to allow excess steam to escape. -For delicate fabrics, we recommend carrying out a test on an unobtrusive area of the garment such as an inner seam. -Adhere to manufacturer recommendations on garment label. 3 Way Auto-Off - If the iron is not moved while it isplugged in, an internal safety switch will turn it off. -It will turn off in 8 minutes if left vertically or in 30 seconds if left on its soleplate or tipped over. A red flashing light indicates that the auto-off has been activated. - To switch the iron on again, move the iron or gently shake it. Auto off is not on/off switch. Always unplug iron when it is not use. Filling with Water - Ensure the iron is unplugged. -Slide the variable steam control completely to the left. -Rest the iron on heel and tilt it foward approximately 1 inch. If the iron is equiped with a covered filling inlet, open the filling inlet by sliding the cover down. -Hold the appliance upright so that the water inlet is horizontal. -Fill with water (containing no additives) to the max mark on the water tank. We recommend using water pitcher rather than filling under the tap. -If you need to add water during ironing, UNPLUG the iron and follow the steps above. -Ensure iron heats back to temperature afterwards, that means thermostat light will go out. Water Recommendations Tap water Rowenta irons are designed to be used with REGULAR TAP WATER (up to 12 grains of hardness). If your water is harder than this, Rowenta recommends mixing half tap water with half distilled water which reduces the hardness; or just use inexpensive bottled spring water. Never use 100% distilled water since this can cause the iron to spit and leak. Softened water There are many types of household water softeners and the water from many of them is perfectly acceptable for use in an iron. However, some types of softeners, particularly those that use chemicals such as salt, can cause the iron to leak or spit during use. If you experience this type of problem, we recommend that you try using inexpensive bottled spring water or untreated tap water. Never use 100% pure distilled water. Once you have changed water it will take several u...