Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
OFFICE LOCATION ONLY. If your appliance needs service, ship the product to your nearest regional service center. If in warranty, Rowenta will repair or replace the product at their discretion. If the product is out of warranty, you will be advised of the cost of repair before any work begins. Our main service centers are listed below: Turnpike Appliance Authorized Appliance 3495A Lawson Blvd. 1644 West Ogden Ave. Oceanside, NY 11572 Downers Grove, IL 60515 516-483-5596 630-852-1550 Service center information is subject to change. Please visit our website at or call our service center information line at 781-306-4620. The information line provides current service center information and listings in California. IMPORTANT SAFETY INSTRUCTIONS When using your iron, basic safety precautions should always be followed, including the following: Read all instructions before using the iron. 1. Use iron only for its intended use. 2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to Min. before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around handle when storing. 5. Always disconnect iron from electrical outlet when filling iron with water or emptying and when not in use. 6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Ship it to the nearest Rowenta Appliance Service Center for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while connected or on an ironing board. 8. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down – there may be hot water in the water tank. 9. The use of accessory attachments is not recommended by Rowenta and may result in fire, electric shock or personal injury. SPECIAL INSTRUCTIONS 01. This is a 1200 or 1400 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 02. If an extension cord is absolutely necessary, a 12-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it can not be pulled or tripped over. 03. After the iron has cooled, wrap the cord loosely around the handle. 04. Your Rowenta appliance is intended for household use only. SAVE THESE INSTRUCTIONS Burst of steam 8 To remove stubborn wrinkles or press in a sharp crease, use the burst of steam button. Press the button firmly, a strong burst of steam penetrates deep into the fabric. Leave an interval of at least four seconds between pressing the burst of steam button. With water in the tank, the burst of steam button can be used as soon as the steam ironing temperature has been reached (l l l). electronic Filling with water 2 Slowly remove the protective label/cover from the soleplate. Holding the iron vertical, pour water into the water filling inlet, up to the "max." mark on the water tank. Plug the iron into the outlet. 1 (Depending on model.) If the iron is not moved while it is plugged in, an internal safety switch will turn it off. It will turn off in 8 minutes if left vertically or in 30 seconds if left on its soleplate or tipped over. A red flashing light indicates that the auto-off has been activated. To switch the iron on again, move the iron or gently shake it. 30 sec. 30 sec. 8 min. electronic electronic Vertical steaming 9 (Depending on model.) Check packaging. This is especially useful for getting wrinkles out of hanging clothes, curtains etc. Warning! Never iron clothes on the body or point your iron at anybody when steaming! electronic E H I K J A B F G L C D electronic 3-way Auto-off Auto off is not an on/off switch. Unplug the iron when it is not in use. TROUBLESHOOTING Problem Possible cause Solution Iron is leaking. DISTILLED WATER DO NOT use 100% pure distilled water, use tap water. In very hard water areas mix half tap water with half distilled to reduce hardness; or use inexpensive bottled spring water. SOFTENED WATER If you experience leaks or spitting, change to untreated tap water or inexpensive bottled spring water. DO NOT use 100% distilled water. Is iron hot enough? Set thermostat to the (lll) position. Allow iron to heat up (light goes out) before using steam. Is auto-off activated? Move iron or gently shake. Overuse of burst of Allow more time between each steam. burst. Warm handle. Auto shut off is The shut off circuit in the handle activated. produces a small amount of heat. This is normal and will stop when iron is switched on. Iron won’t heat....