Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
• IMPORTANT — Save these instructions for local inspector’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • Product failure due to improper installation is not covered under the Warranty. WARNING — This appliance must be properly grounded. • ATTENTION INSTALLER — ALL COOKTOPS MUST BE HARD WIRED (DIRECT WIRED) INTO AN APPROVED JUNCTION BOX. A “PLUG AND RECEPTACLE” IS NOT PERMITTED ON THESE PRODUCTS. • Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty. Saber Saw Pencil Safety Glasses 1/8. Drill Bit & Electric or Hand Drill Ruler or Straightedge Phillips Head Screwdriver PHP960, ZHU36 “If you have questions, call 800.GE.CARES or visit our website at: ge.com” 31-10668 (06 -07 JR) 1/4. Nut Driver MATERIALS YOU WILL NEED Large Size Wire Nuts Junction Box (Sized for conduit per local electrical codes.) 90. or Straight Squeeze Connector for 1” Conduit PARTS INCLUDED Baffle (For all installations except over an oven.) Foam Tape 2 Hold-Down Brackets 6 Hex-Head Screws 2 Thumbscrews Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY • For Personal Safety, remove house fuse or open circuit breaker before beginning installation. Failure to do so could result in serious injury or death. • Be sure your cooktop is installed properly by a qualified installer or service technician. • To eliminate the risk of burns or fire due to reaching over heated surface elements, cabinet storage located above the surface units should be avoided. If cabinet storage space is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5. beyond the bottom of the cabinets. Cabinet installation above the cooktop may be no deeper than 13.. • Make sure the cabinets and wall coverings around the cooktop can withstand the temperatures (up to 200°F) generated by the cooktop. • The cooktop should be easy to reach and lighted with natural light during the day. • Always disconnect the electrical service to the cooktop before repairing or servicing the cooktop. This can be done by disconnecting the fuse or circuit breaker. Failure to do this could result in a dangerous or fatal shock. Know where your main disconnect switch is located. If you do not know, have your electrician show you. ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or a time delay fuse as noted on name plate. We recommend you have the electrical wiring and hookup of your cooktop connected by a qualified electrician. After installation, have the electrician show you where your main cooktop disconnect is located. Wiring must conform to National Electrical Code and all local electrical codes. You can get a copy of the National Electrical Code, ANSI/NFPA No. 70-Latest Edition, by writing: National Fire Protection Association Batterymarch Park Quincy, MA 02269 In Canada, wiring must conform to Canadian Electrical Code (CEC). The cooktop conduit wiring is approved for copper wire connection only, and if you have aluminum house wiring, you must use special UL approved connectors for joining copper to aluminum. In Canada, you must use special CSA approved connectors for joining copper to aluminum. You must use a two-wire, three conductor 208/240 VAC, 60 Hertz electrical system. A white (neutral) wire is not needed for this unit. Refer to the name plate on your cooktop for the KW rating for your cooktop. These cooktops require 50 amp service. Name plate location 2 3 Installation Instructions BEFORE YOU BEGIN WARNING – The electrical power to the cooktop supply line must be shut off while connections are being made. Failure to do so could result in serious injury or death. When preparing cooktop opening, make sure the inside of the cabinet and the cooktop do not interfere with each other. (See section on preparing the opening.) Remove packaging materials and literature package from the cooktop before beginning installation. Remove Installation Instructions from the literature pack and read them carefully before you begin. Be sure to place all literature, Owner’s Manual, Installations, etc. in a safe place for future reference. Make sure you have all the tools and materials you need before starting the installation of the cooktop. Your home must provide the adequate electrical service needed to safely and properly use your cooktop. (Refer to section on electrical requirements.) When installing your cooktop in your home, make sure all local codes and ordinances are followed exactly as stated. Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat (up to 200°F) generated by the cooktop. G F E D C B A ADVANCE ...