Log:
Assessments - 3, GPA: 4.3 ( )

Instruções de Operação DCS, Modelo CT-304SS

Fabricante : DCS
Arquivo Tamanho: 1021.67 kb
Arquivo Nome :
Língua de Ensino: enfr
Ir para baixar



Facilidade de uso


Spray the dirty area with Easy Off® or SOS Oven Cleaner® when cool. Cover with paper towel. Leave on for 4 hours or overnight.With a warm wet sponge, wipe clean and polish with a lint free soft towel.You should never use anything stronger than a sponge or a plastic non-metal sponge on your cooktop. For your convenience, a sample bottle of Stainless Steel Magic® has been included with your cooktop. DO NOT use this or similar products on bezels and knobs. Discoloration may occur. BRAND NAMES: In this section, the use of name brands is intended only to indicate a type of cleaner. This does not constitute an endorsement. The omission of any name brand cleaner does not imply its adequacy or inadequacy. Many products are regional in distribution and can be found in the local markets and department stores. CLEANING THE BURNER GRATES: Turn off all the burners and allow the grates to cool before starting to clean the cooktop. Rapid cooling of the grates, for instance, placing hot grates in cool or tepid water to clean, can thermally shock the porcelain coating and cause cracking or chipping. If you wipe off any part of the cooktop while it is hot, do so carefully as using a wet sponge or cloth can result in steam burns. Once the grates are cool they may be wiped clean while on the cooktop using hot soapy water, then rinsed and wiped dry or they may be placed in the dishwasher for easy cleaning.The occasional use of mild abrasive cleansers such as Bon-Ami®, Soft Scrub® or a soap-filled plastic or non-metal pad is okay. Abrasive cleansers, used vigorously or too often, can eventually harm the enamel. Apply with a damp sponge, rinse thoroughly and dry. 8 CARE AND MAINTENANCE CLEANING THE BURNERS: For proper lighting and performance, keep the burners clean and dry. It is necessary to clean the burners if they do not light although the igniter clicks, whenever there has been a severe boil over or when the flame doesn't burn blue. Be certain all burner knobs are in the OFF position before attempting to clean the burners. The burners have been designed for ease of cleaning. When the grates and burners are cool, remove the grate.The Burner Cap and the Brass Port Ring can easily be lifted off.Wash these parts in hot soapy water, rinse and dry thoroughly. The Burner Caps are porcelain enamel, follow the directions on page 8 that were given to clean the burner grates. A bristle brush can be used to clean out the toothed burner ports, if necessary. Disassembly of the Simmer Ring is not recommended, however, it may become necessary to do so if the ports remain clogged after normal cleaning.If it is necessary to disassemble the Simmer Ring from the Base,remove the Hex Nut at the top of the Simmer Ring. Clean the Simmer Ring with hot soapy water using a soft wire or plastic bristle brush then dry thoroughly. Re-assemble the parts using the Hex Nut. After cleaning, it is important to make sure the Locating Pin on the bottom side of the Simmer Ring is properly aligned with the corresponding hole in the Base and that the Locating Pin (see above) in the bottom side of the Brass Port Ring is properly aligned with the Locating Notch on the top side of the Simmer Ring. Incorrect alignment will produce a potentially dangerous flame and poor burner performance. See the illustration above. Brass Port Ring Locating Pin Locating Notch Locating Pin Locating Pin Hole Inside Brass Port Ring Hex Nut Simmer Ring Base CLEANING THE IGNITERS: Be certain all burner knobs are in the OFF position before attempting to clean the igniters. Gently wipe with an alcohol dampened cotton swab and be careful not to damage the igniter. 9 PRODUCT MEASUREMENT SPECIFICATIONS Dimensions shown below are for product reference only. REFER TO THE PRODUCT INSTALLATION GUIDE FOR CABINET PREPARATION AND CUTOUT SPECIFICATIONS. CT-365 Grate (p/n 12268-01)(2 pcs) 'C' Burner Cap (p/n 12273)(4 pcs) Knob (p/n 14301)(5 pcs) 36" Front View "B" 2-3/4" 34-1/2" R Side View I 4" + 5-1/2 1 t ini /->" 2-7/8" 10 PRODUCT MEASUREMENT SPECIFICATIONS Dimensions shown below are for product reference only. REFER TO THE PRODUCT INSTALLATION GUIDE FOR CABINET PREPARATION AND CUTOUT SPECIFICATIONS. CT-304 Grate (p/n 12325)(2 pcs) Top View ft] \jk f\! (VI on %= IV U=] ¥1 30" 'D'Burner Cap (p/n 12272)(1 pcs) Front View 'C'Burner Cap (p/n 12273)(3 pcs) Knob (p/n 14301)(4 pcs) 21 - 2-11/16" 28-5/16" R Side View I 4" 5-1/2" - 1-1/2" -19-1/2"- 11 SERV...

Este manual também é adequado para os modelos :
Hobs - CT-365BK (1021.67 kb)
Hobs - CT-365BK (1021.67 kb)
Hobs - CT-365WT (1021.67 kb)
Hobs - CT-304BK (1021.67 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias