Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Accumulated baked-on stains/ dirt, sugar spills or melted plastics Cleaning sponge or glass scraper and soft cloth Wipe over the zone to be cleaned with a sponge and hot water, using a ceramic scraper to remove any large marks or stains and then wipe off with a soft dry cloth. Rings and hard water residues White vinegar and soft cloth Pour a small amount of warm white vinegar onto the stain, leave it to stand, and then wipe off with a soft dry cloth. 7Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Do not use steel wool, abrasive sponges or sharp utensils such as knives to clean the hob as these could damage the hob. The hob surface and the pans must be clean. Carefully remove any food remains (especially those containing sugar), dirt etc. as soon as is possible after spillage - using a ceramic hob scraper if necessary whilst the zone is still hot. Once they have cooled and hardened they become increasingly difficult to remove. Sugar, syrup and starch mixtures could permanently pit the hob surface if left to burn on and should be removed as quickly as possible after spillage. The stainless steel trims should be rinsed with water and dried with a soft, clean cloth, a chamois leather or an E-Cloth. If necessary, the control knobs can be removed for cleaning, but you should take care not to damage the seal nor to allow water inside the hob itself. All cleaner residues should be removed with a damp cloth. Important: • Steam cleaners must not be used when cleaning this appliance. Mains electrical voltage: 230 – 240Vac Total rated electrical consumption: HVC60 6.9 kW HVC70 6.8 kW HVC90 8.6 kW If your Hob is not working: 1. Check that the control knobs are switched on. 2. Check that the mains supply has not been switched off. 3. Check that the fuse in the spur has not blown. Contact CDA Customer Care A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : Types of residues Clean with Cleaning advice Light Cleaning sponge and soft cloth Wipe over the zone to be cleaned with a sponge and hot water, and then wipe off with a soft dry cloth. Accumulated baked-on stains/ dirt, sugar spills or melted plastics Cleaning sponge or glass scraper and soft cloth Wipe over the zone to be cleaned with a sponge and hot water, using a ceramic scraper to remove any large marks or stains and then wipe off with a soft dry cloth. Rings and hard water residues White vinegar and soft cloth Pour a small amount of warm white vinegar onto the stain, leave it to stand, and then wipe off with a soft dry cloth. 7 Mains Electricity Connection Warning! this appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or 13A supply. This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at least 3mm in all poles. The switch must be positioned no further than 2m from the appliance. Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 2.5 mm. for HVC60/HVC70, 4mm. for HVC90, HO5RR-F, HO5VV-F or H05V2V2-F). • This appliance is intended to be connected to the mains supply with a cable of cross section area 2.5 mm. (HVC60/70) or 4mm. (HVC90). A larger cable will not fit the terminal connections. • The marking of the current rating of the fuse or circuit breaker protecting this appliance should be marked on the socket outlet. • Assembly and electrical connection should be carried out by specialised personnel. • When installing this product we recommend you seek the help of another individual. • Ensure that the brass links are securely fitted. Failure to do so will prevent the hob from operating correctly. ABCB Fig.10 Fig.11 12354NELFDCGE Fitting the Hob Unpacking the hob: • Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant to fire (tiles or steel, for example). These dimensions are shown in Fig.12. If fitting a cooker hood above the hob: If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is recommended) (Fig.13). If the instructions supplied with the hood dictate that the hood must be installed at a ...
Este manual também é adequado para os modelos :Hobs - HVC60 (2.3 mb)
Hobs - HVC70 (2.3 mb)