Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
– The appliance must be installed correctly, in compliance with the regulations in force and following the manufacturer's instructions. – Any repair or maintenance must be performed with the appliance switched off. – These appliances have been designed and manufactured to be fitted into heat-resistant units. – These hobs are designed to be fitted into 600mm deep kitchen units. – The unit walls must not be higher than the working surface and must withstand a temperature of 105°C above room temperature. – Avoid installation near inflammable materials (e.g. curtains). Ventilation Requirements – The appliance should be installed into a room or space with an air supply in accordance with BS 5440-2: 2000. – For rooms with a volume of less than 5m3 -permanent ventilation of 100cm2 free area will be required. – For rooms with a volume of between 5m3 and 10m3 a permanent ventilation of 50cm2 free area will be required unless the room has a door which opens directly to the outside air in which case no permanent ventilation is required. – For rooms with a volume greater than 10m3 - no permanent ventilation is required. Important ! Regardless of room size, all rooms containing the appliance must have direct access to the outside air via an openable window or equivalent. – Where there are other fuel burning appliances in the same room, BS 5440-2: 2000 should be consulted to determine the correct amount of free area ventilation requirements. – The above requirements allow also for use of a gas oven and grill but if there are other gas burning appliances in the same room, consult a qualified engineer. 13 Installation Technical Information for the Installer In order to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 12 has to be made, bearing in mind the following: – Within the unit, between the bottom of the hob and the upper surface of a shelf there must be a clearance of at least 30mm. – It is absolutely essential that you place a separator between the base of the hob and the built-in unit or the oven. – The hob must be kept no less than 200mm away from any side wall (fig. 12). – The hob must be installed at least 60mm from the wall. – There must be a distance of at least 650mm between the hob and any wall cupboard or extractor hood positioned immediately above (see fig. 14). – If the hob is installed over a builtin oven, there must be a distance of at least 30mm between the two appliances. The two appliances should be connected to the gas supply with independent connections 650 mm 450 mm 480 60 0 –2 560 200 0 –2 680 500 Installation in Kitchen Cabinet with Door It is recommended that a 30mm clearance be left between the cooktop and the fixture surface (fig. 13). 30 mm Space for connections Clearance Door Fig. 12 Fig. 13 Fig. 14 14 Applying the Seals – Turn the cooktop upside down. – Spread the longer seal “A” around the left, rear and right sides as shown in figure 15a. – With a cutter or a scissors cut the excess seal “C” and retain it for next use (figure 15b). – Spread the seal “B” around the left, front and right edges of the cooktop as shown in figure 15c. – Spread the seal “C” along the rear edge of the cooktop as shown in figure 15d. Making sure that the beginning and the end overlap at the seal “B” (see figure 15e). Fig. 15a Fig. 15b Fig. 15c Fig. 15d Front side seal A seal C seal A seal C seal B seal C seal B Fig. 15e 14 Applying the Seals – Turn the cooktop upside down. – Spread the longer seal “A” around the left, rear and right sides as shown in figure 15a. – With a cutter or a scissors cut the excess seal “C” and retain it for next use (figure 15b). – Spread the seal “B” around the left, front and right edges of the cooktop as shown in figure 15c. – Spread the seal “C” along the rear edge of the cooktop as shown in figure 15d. Making sure that the beginning and the end overlap at the seal “B” (see figure 15e). Fig. 15a Fig. 15b Fig. 15c Fig. 15d Front side seal A seal C seal A seal C seal B seal C seal B Fig. 15e 15 15 fixture panels from 2 to 4 cm thick. Fastening the Cooktop – position. – Fastening the Installation Brackets Each cooktop is provided with an installation kit including brackets and screws for fastening the top to – Turn the cooktop upside down and fasten the brackets “F" and "R” to the appropriate socket holes, without tightening the screws “B” for the moment. – Make sure that the brackets are fastened as shown in figures 16a, 16b and 16c. Insert the cooktop into the hole and position it correctly. – Adjust the position of the brackets “F" and "R” and tighten screws “B” to block the cooktop firmly in With a sharp cutter or trimmer knife trim the excess sealing material around the edge of the cooktop. Take care not to damage the workbench. R R F FFig. 16a 20 mm min.40 mm max.20 mm min.40 mm max.B F B R Front side Rear side Fig. 16c Fig. 16b Front side Rearside 16 16 Gas Supply Requirements Important Note This appliance is supplied for use on NATURAL GAS or ...
Este manual também é adequado para os modelos :Hobs - HCG 731 (1.07 mb)