Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
It must be installed and connected in accordance with current installation regulations. Particular attention should be given to the relevant requirements regarding ventilation. GAS SAFETY (INSTALLATION & USE) REGULATIONS It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the above regulations. It is in your interest and that of safety to ensure compliance with the law. In the UK, CORGI registered installers work to safe standards of practice. The cooker must also be installed in accordance with BS 6172: Failure to install the cooker correctly could invalidate the warranty liability claims and could lead to prosecution. LOCATION The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in a room containing a bath or shower. The cooker must not be installed in a bedsitting room of less than 20m3. PROVISION FOR VENTILATION The room containing the cooker should have an air supply in accordance with BS 5440: Part 2. The room must have an opening window or equivalent; some rooms may also require a permanent vent. If the room has a volume between 5 and 10m3, it will require an air vent of 50cm2 effective area unless it has a door which opens directly to outside. If the room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area. If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be consulted to determine air vent requirements. 11 FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 12 INSTALLATION SITING THE HOB The hob is designed to fit into worktop and base unit(s) with a cutout as shown in Fig.1. Any obstruction such as supports or side panels must be removed to allow 30mm minimum depth below the worktop cutout. Any overhead surface of combustible material must not be closer than 600mm. When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above the hotplate a side clearance of at least 40mm should be allowed from the edge of the cutout. This is a type X appliance regarding installation requirements, it is recommended that a shelf is fitted to the cabinet under the hob, but no closer than 10mm to prevent access to the underside of the hob which will become hot when in use. If a cooker hood is to be installed refer to the manufacturer’s instructions regarding fixing heights. FITTING THE HOB Unpack the hob from the carton. Remove the bag containing the sealing tape, fixing brackets, screws and gas inlet elbow. Fit the sealing tape around the edge of the cut-out in the worktop. Connect the gas inlet elbow supplied to the end of the hob gas pipe. During installation, it is important not to twist the hob gas pipe when connecting to or adjusting the position of the gas inlet elbow to avoid the possibility of disturbing gas tight joints inside the hob. Ensure that the inlet is held securely: * When loosening or tightening the hob gas pipe securing nut. * When connecting fittings to it. Also, ensure that connecting pipe work does not twist the inlet elbow away from its free position. Lower the hob into the worktop ensuring the mains lead is fed into the base unit and is not trapped under the flanges. Fix the hob to the worktop using the fixing brackets and screws. NB Do not over tighten the hob clamps as distortion of the hob may occur. Connect the hob to the gas supply and check for gas soundness. If a flexible hose is used for connection, it should be fitted such that it cannot come into contact with moveable parts of the housing (e.g. a drawer), does not pass through a space where it is likely to become trapped or damaged and hangs freely downwards. The temperature rise of the area of the base panel likely to come into contact with a flexible hose does not exceed 70.C Connection must be by rigid pipework when the hob is installed above an oven. Put the burner rings and caps into position. Connect the hob to the electrical supply (see INSTALLATION - Electrical Requirements). Ensure that the hob is functioning correctly prior to use. Instruct the user in the operation of the hob. 12 FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 13 INSTALLATION Fig. 1 IMPORTANT Minimum unobstructed depth 50mm Worktop thickness Preferred 30-40mm 19mm minimum recommended 30mm 489mm558mm Front edge of worktop Fig. 2 FIXING CLAMP Note: Do not over tighten the hob clamps as distortion of the hob may occur. 13 FP087-01 HP Gas Hob (BG05) 12/09/2001 5:00 pm Page 14 INSTALLATION INSTRUCTIONS LPG Conversion Instructions for Models W810, BG05 Read the Gas Hob instructions before conversion, installation and using the Gas Hob. Contents of kit: 1 Rapid burner injector marked 92 - 1 off 2 Semi-rapid burner injector marked 72 - 2 off 3 Auxillary burner injector marked 55 - 1 off Hotplate Burner Injector Change and Bypass Screw Adjustment Ensure that the Gas Hob is disconnected from the gas and electricity supply (Fig.1) 1. Remove pan supports, burner caps,bur...