Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Place the pans on the pan supports, never directly on the burner. Pans should be placed on the cooktop carefully. Do not strike the cooktop and do not place excessive weight on it. Make sure that the pan supports and burner covers are correctly positioned before using the appliance. Cleaning and maintenance Cleaning Unsuitable products Maintenance Once the appliance is cool, use a sponge to clean it with soap and water. After each use, clean the surface of the respective burner parts once they have cooled down. If any residue is left (baked-on food, drops of grease etc.), however little, it will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly. The movement of some pans may leave metal residue on the pan supports. Clean the burners and pan supports using soapy water and scrub with a non-wire brush. If the pan supports are fitted with rubber rests, ensure that these are also cleaned. The rests may come loose and the pan support may scratch the hob. Always dry the burners and pan supports completely. Water droplets or damp patches on the hob at the start of cooking may damage the enamel. After cleaning and drying the burners, make sure the burner covers are correctly placed on the diffuser. Do not use steam cleaners. This could damage the hob. If your hob is fitted with a glass or aluminium panel, never use a knife, scraper or similar to clean the point where it joins the metal. Always clean off any liquid as soon as it is spilt: you will save yourself any unnecessary effort. Do not leave acidic liquids (e.g. lemon juice, vinegar, etc.) on the hob. Where possible, do not allow salt to come into contact with the surface of the electric hob. The ring cover of the double or triple flame burner and stainless steel parts such as hotplate rings, top sheet and the area around the burners may become discoloured over time. This is normal because of the high temperatures. Each time the appliance is used these parts should be cleaned with a product that is suitable for stainless steel. The stainless steel cleaner must not be used in the area around the controls. The (printed) symbols may be wiped off. DO NOT MODIFY THIS APPLIANCE. Service Only authorized personnel from the Service Centre are qualified to work on the appliance. Sometimes certain faults detected can be easily resolved. Before calling the Service Centre, bear in mind the following advice: Fault Possible cause Solution The general electrical Defective fuse. Check the fuse in the main fuse system is malfunctioning. The automatic safety switch or circuit breaker has tripped. box and change it if it is damaged. Check the main control panel to see if the automatic safety switch or circuit breaker has tripped. The automatic on There may be food or cleaning The space between the ignition function does not work. products stuck between the ignition sparkers and the burners. The burners are wet. The burner covers are not correctly positioned. The appliance is not earthed, is not correctly connected or the earth wire is faulty. sparker and the burner must be clean. Dry the burner covers carefully. Check that the covers are correctly positioned. Contact the electrical installer. The burner flame is not uniform. The burner components are not correctly positioned. The grooves on the burner are dirty. Ensure the components are correctly positioned. Clean the grooves on the diffuser. The flow of gas does not appear normal or no gas comes out. The gas supply is blocked via intermediary valves. If the gas is supplied from a gas cylinder, check that this is not empty. Open all intermediary valves. Change the gas cylinder. The kitchen smells of gas. A gas tap has been left on. There may be a leak in the gas cylinder coupling. Possible gas leak. Turn off the gas taps. Check that the coupling is sound. Shut off the gas supply, ventilate the premises and immediately notify an authorised installation technician so that they can check and certify the installation. Do not use the appliance until you are sure that there is no gas leak in the installation or appliance itself. The safety valves on one of the burners are not working. The control knob was not held down for long enough. The grooves on the diffuser are dirty. Once the burner is lit, hold the control knob down a few seconds longer. Clean the grooves on the diffuser. Any of the following are considered to be abnormal operation and may require servicing: Yellow tipping of the cooktop burner flame. Sooting up of cooking utensils. Burners not lighting properly. Gas valves, which are difficult to turn in case the appliance fails to operate correctly, contact the authorised service provider in your area. Wiring diagram A. Switch B. Blue wire C. Brown wire D. Terminal E. Ignition module CIF: A-28-893550 ROBERT BOSCH HAUSGERATE GMBH !:PCH615B9TA . '(. !. ULPG 01. 12 Test point pressure (kPa) Injectors marks LHF . 85/140 46/71 L...