Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Always clean off any liquid as soon as it is spilt: you will Maintenance save yourself any unnecessary effort. Do not leave acidic liquids (e.g. lemon juice, vinegar, etc.) on the hob. Where possible, do not allow salt to come into contact with the surface of the electric hob. The ring cover of the double or triple flame burner and stainless steel parts such as hotplate rings, top sheet and the area around the burners may become discoloured over time. This is normal because of the high temperatures. Each time the appliance is used these parts should be cleaned with a product that is suitable for stainless steel. The stainless steel cleaner must not be used in the area around the controls. The (printed) symbols may be wiped off. Faults Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Fault Possible cause Solution The general electrical system is malfunctioning. Defective fuse. The automatic safety switch or circuit breaker has tripped. Check the fuse in the main fuse box and change it if it is damaged. Check the main control panel to see if the automatic safety switch or circuit breaker has tripped. The automatic on function does not work. There may be food or cleaning products stuck between the ignition sparkers and the burners. The burners are wet. The burner covers are not correctly positioned. The appliance is not earthed, is not correctly connected or the earth wire is faulty. The space between the ignition sparker and the burner must be clean. Dry the burner covers carefully. Check that the covers are correctly positioned. Contact the electrical installer. The burner flame is The burner components are Ensure the components are not uniform. not correctly positioned. The grooves on the diffuser are dirty. correctly positioned. Clean the grooves on the diffuser. The flow of gas does The gas supply is blocked Open all intermediary valves. not appear normal or via intermediary valves. Change the gas cylinder. no gas comes out. If the gas is supplied from a gas cylinder, check that this is not empty. The kitchen smells of gas. A gas tap has been left on. There may be a leak in the gas cylinder coupling. Turn off the gas taps. Check that the coupling is sound. The safety valves on one of the burners are not working. The grooves on the diffuser are dirty. Clean the grooves on the diffuser. The childproof lock indicator light comes on. The electricity has come back on after a power failure or voltage drop. Deactivate the childproof lock (see page 10). If the problem continues contact the Technical Assistance Service. Operating indicators and error messages Main switch indicator lit. Main switch indicator and all “power on/off” indicators lit. “Power on/off” indicator in one burner lit. The childproof lock indicator light comes on. Main switch indicator lit, “power on/ off” indicator in one burner flashes. Main switch indicator off, “power on/off” indicator on one burner flashes. Main switch indicator and all “power on/off” indicators flash simultaneously. Main switch indicator off, all “power on/off” indicators flash one after the other. Appliance ready for use. All the burners are switched on or are still hot. Residual heat indicator, the burner is still hot. Childproof locks activated. Burner cannot be reignited (dirty, boiled-over liquid on the burner, burner parts not correctly positioned, strong draught). Control error, control knob opened without first turning on the main switch -or - safety shut off – appliance was in use for over 6 hours. Overheating protection – turn all control knobs to 0 and allow the appliance to cool until the “power on/off” indicator goes out or switches over to the residual heat indicator. Electronics fault – turn all control knobs to 0, reset the appliance (press the main switch twice). If the displays still flash, contact the Technical Assistance Service. Technical Assistance Service When contacting our Technical Assistance Service, please provide the product number (E-No.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual. Warranty conditions The applicable warranty conditions are those set out by the company's representative office in the country of purchase. Detailed information is available from retail outlets. Proof of purchase must be presented to obtain the benefits of the warranty. We reserve the right to introduce changes. Used appliances and packaging If the ) symbol is shown on the specifications plate, bear in mind the following instructions. Environmentally-friendly waste Unpack the appliance and dispose of the packaging by management environmentally-friendly means. This appliance complies with European directive 2002/ 96/CE on electrical and electronic equipment identified as WEEE (waste electrical and electronic equipment). Table des matieres Consig...
Este manual também é adequado para os modelos :Hobs - PCR715F90E/07 (1.86 mb)