Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
When assembling the burner parts, make sure that the burner head is placed on the base in such a way that the prongs of the burner cap fit snugly into the groove of the burner base. Checking Burner Cap Placement Check to make sure that there is no gap between the burner parts. You may gently try to move the burner parts from side to side to check if they are properly placed. Check the Installation Check operation of electric igniters. Check flame characteristics. Flame should be blue with no yellow tip. Yellow Flames: Further adjustment is required. Yellow Tips on Outer Cones: Normal for LPG Gas. Soft Blue Flames: Normal for Natural Gas. If the flame is completely or mostly yellow, verify that the regulator is set for the correct fuel. After adjustment, retest. Some yellow streaking is normal during the initial start- up. Allow unit to operate 4- 5 minutes and reevaluate before making adjustments. Removing the appliance Disconnect the appliance from the power supply. Close the gas shut-off valve. Remove the silicone joint from appliances installed flush. Push out the appliance from below. 9 CAUTION Appliance damage! Do not lever out the appliance at the frame from above. Conversion to another type of gas This gas stovetop corresponds to the categories specified on the rating plate. By changing nozzles, it is possible to convert the appliance to any of the gases listed on the plate. The conversion kit can be obtained from our customer service. With some models, the conversion kit is included in the scope of delivery. Only a licensed specialist is authorized to switch the appliance to another gas type. Before carrying out the conversion, turn off the electricity and gas supply. 4<;6364<;34.4<6.<;4.4<6.<; Replacing the low- setting nozzles 1 Remove the pan support and all burner parts. 2 Undo the cooktop's fastening screws on the burners and carefully remove the cooktop in the upward direction. Unscrew the cover plate over of the spindles. 3 Remove the locking screw of the spindles between the control knob and gas valve and extract the spindles from the gas valve. Remove the cover plate in front of the gas valve. The low- setting nozzles are located in the gas valve and are screwed in from the front. Turn the plastic part on the gas valve so that the recess is above the respective nozzle. Unscrew the nozzle and pull it out with a small pair of pliers. 5 Fully screw in the new low-setting nozzles as detailed in the table of nozzles. 6 Slide the spindles onto the gas valve and firmly tighten the locking screws. Fit and firmly tighten the cover plates. Replacing the main nozzles 1 Detach the securing clips from the burner pipes. Unscrew the burners and extract the burner pipes. The electrode can be left connected. Extract the burners from the burner pipes. 2 Extract the nozzles from the burner pipes by hand and extract the O- ring. 3 Check correct fitting of the O-ring in the new main nozzles. Slide the nozzles onto the burner pipes. Do not bend the burner pipes! 4Fit the burners onto the burner pipes. Fit the burners. Screw down the burners. 5After loosening the screw, adjust the outer burner's air regulation sleeve to the correct dimensions ( see nozzle table - L1) . Tighten the screw again. 6 By turning or moving it, adjust the inner burner's air regulation sleeve to the correct dimension ( see nozzle table - L2) . .4 .< 7 Fit the cooktop and screw it down evenly. Fit burner parts and pot supports, paying attention to correct positioning. 8 Set the pressure regulator to the correct pressure (see “Connect gas supply”). Checking functions after the conversion: The flames are adjusted correctly if no yellow tips are visible. They must not go out when switching over swiftly from the high to the low setting. Note: Stick the adhesive label included with the nozzle set over the rating plate of the appliance to document the changeover to a different gas type. Customer service If your appliance needs repairs, our customer service is there for you. We work hard to help solve problems quickly and without unnecessary service calls, getting your appliance back up and running correctly in the least amount of time possible. When you call, please indicate the product number (E- Nr. ) and serial number (FD-Nr. ) so that we can support you in a qualified manner. You will find the type plate with these numbers on the bottom of the appliance. To avoid having to search for a long time when you need it, you can enter your appliance data and the customer support telephone number here. E- Nr. FD- Nr. Customer Service O Please read the installation instructions and use and care instructions provided with your appliance. Failure to do so may result in an error in using the appliance. This could result in a service call that instead of fixing a mechanical issue is only needed for customer education. Such calls are not covered by the appliance warranty. Please find the contact data of all countries in the enclosed cu...