Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
This appliance may be installed in kitchen combinations made of wood or similar combustible materials without taking additional safety measures. The built-in furniture and worktop where the appliance is installed must be heat resistant up to temperatures of 200° F/90° C. The appliance must only be connected by an authorised specialist, following the relevant regulations of the power supply companies and the regional construction regulations and codes. When connecting electrical appliances in the proximity of cooking surfaces, make sure that connecting cables do not come into contact with hot cooking surfaces. The installation technician is responsible for the correct functioning of the appliance at the place of installation. He must instruct the user how to disconnect the appliance from electricity in an emergency. After unpacking, check the appliance for any transportation damage and report this immediately to the transportation company. Protection against accidental contact from below must be provided by an intermediate shelf that can only be removed with a tool. The distance from the top of the work surface to the top of the intermediate shelf must be at least 150 mm (6. . ). There must be a gap of at least 40 mm (19/16 . . ) at the side between the appliance and any walls or furnishings. No warranty claims can be lodged for any damage resulting from failure to observe these instructions. Pay attention to the “Important notes" on page 3 and 4. Subject to technical change without notice. Electrical connection Only a qualified electrician should install this appliance. This appliance must be hardwired. The mains connecting cable must at least correspond to the type SJTO 3x16 AWG 105°C. The mains connecting cable must only be purchased through and connected by an authorised specialist. The appliance must be properly grounded. Pay attention to the information on the rating plate on the bottom of the unit. Preparing the cabinet 2 1 5 4 3 A The building back wall (1) and building side walls (2 / 3) must consist of non combustible material or must be protected by no less than 1/4-inch-thick flame- retardant millboard covered with no less than No. 28 MSG sheet steel, 0.015-inch-thick stainless steel, 0.024-inch-thick aluminimum, or 0.020-inchthick copper. 1 Building back wall 2 Building side wall 3 Building side wall 4 Top building cabinet 5 Grilling surface A = 30 inch (762 mm) Preparing the cabinet 51/2" (140) 8 11 /16" 20 1/16 " 14 15/16" (220) (76) (280) 11" min. (105) max. (162,5) (510) (380)5/16" 2 3/4" 115 /16 " 1 3/8" 115 /16" 4 1/8" 3 9/16 " 14 3/16"14 3/16" 2 3/8" 1 3/8" 6 3/8 " 19 5/16" (70) (50) (490) (360) min. (35) min. (50) (35) (60) (90) 3" (8) • Cut out the recess for one or several Vario appliances in your worktop. Proceed as indicated on the installation sketch. The installation sketch contains the measurements of the space required for the trim between the appliances. Several appliances can also be installed in individual recesses, as long as a minimum clearance of 50 mm (2 . . ) is kept to between the appliances. • As shown in the installation sketch, drill the O 35 mm (13/8 . . ) holes to secure the control knobs in the cabinet front. • If the cabinet front is thicker than 26 mm (1 . . ), the front must be routed from the back to max. 26 mm (1 . . ) on an area of 80 x 310 mm (31/8 . . -123/16 . . ). min. 3/16" (5) min. 3/16" (5) – 1" 3 1/8" 5/8" (16 – 26) (80 x 310) x 12 3/16" D = 1" (26) D > 1" (26) Installing the control panel • Before installation, remove all styrofoam packaging from the control knobs and peel off the protective film behind the luminous discs. • Hold the support plate from the rear against the cabinet front, insert control knobs into the holes, secure from the rear with the nuts. Take care to install control knobs in the correct order: left control knob for selecting the frying zone, right for temperature control knob. • Secure the control panel with the included nuts onto the support plate. 18 m Caution! Only install control panel with appliance of the corresponding type. m Caution! Before connecting the appliance, make sure the electricity is switched off at fuse point! Installing the appliance • Firmly plug the connecting cable in the appliance and in the control panel (the plugs must lock into place). • T urn the clamping screws to the side. Insert the appliance with the control panel on the front into the cut-out and align it. Note: do not stick the appliance onto the worktop with silicone. • T urn the clamping screws under the countertop and tighten them evenly. Do not tighten the clamping screws too tightly, as a uniform sealing gap should be left all round. • Connect the appliance to the electricity. Test that it functions correctly. If the luminous discs behind both control knobs blink alternately, check the connecting cable between the appliance and the control panel is firmly plugged in. 9000125749 EB 8801 enUS GAGGENAU HAUSGERATE GMBH 780 DEDHAM STREET CARL-W...
Este manual também é adequado para os modelos :Hobs - VP421610/11 (454.06 kb)