Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Pans should be placed on the hob carefully. Do not strike the hob and do not place excessive weight on it. Cleaning and maintenance Cleaning Once the appliance is cool, use a sponge to clean it with soap and water. After each use, clean the surface of the respective burner parts once they have cooled down. If any residue is left (baked-on food, drops of grease etc.), however little, it will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly. The movement of some pans may leave metal residue on the pan supports. Clean the burners and pan supports using soapy water and scrub with a non-wire brush. If the pan supports are fitted with rubber rests, ensure that these are also cleaned. The rests may come loose and the pan support may scratch the hob. Always dry the burners and pan supports completely. Water droplets or damp patches on the hob at the start of cooking may damage the enamel. After cleaning and drying the burners, make sure the burner caps are correctly positioned on the diffuser. Caution! ¦ Do not use steam cleaners. This could damage the hob. ¦ If your hob is fitted with a glass or aluminium panel, never use a knife, scraper or similar implement to clean the point where it joins the metal. Maintenance Always clean off any liquid as soon as it is spilt. This will prevent food remains from sticking to the hob surface and you will save yourself any unnecessary effort. Due to the high temperatures endured, the wok burner and the stainless steel zones (grease drip tray, burner outline, etc.) can change colour. This is normal. After each use, clean these areas with a product that is suitable for stainless steel. It is recommended that the cleaning product available from our Technical Assistance Service (code 464524) is used regularly. Caution! The stainless steel cleaner must not be used in the area around the controls. The (printed) symbols may be wiped off. Do not leave acidic liquids (e.g. lemon juice, vinegar, etc.) on the hob. Trouble shooting Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Fault Possible cause Solution The general electrical sys-Defective fuse. Check the fuse in the main fuse box and change it tem is malfunctioning. if it is damaged. The automatic safety switch or circuit breaker has Check the main control panel to see if the auto- tripped. matic safety switch or circuit breaker has tripped. The automatic switching on There may be food or cleaning products stuck The space between the ignition sparker and the function does not work. between the ignition sparkers and the burners. burner must be clean. The burners are wet. Dry the burner caps carefully. The burner caps are not correctly positioned. Check that the burner caps are correctly positioned. The appliance is not earthed, is poorly connected Contact the installation technician. or the earthing is faulty. The burner flame is not uni-The burner components are not correctly posi-Correctly place the parts on the appropriate form. tioned. burner. The grooves on the burner are dirty. Clean the grooves on the burner. The gas flow is not normal The gas supply is blocked by gas taps. Open all gas taps. or there is no gas. If the gas is supplied from a gas cylinder, check Change the gas cylinder. that it is not empty. The kitchen smells of gas. A gas tap has been left on. Turn off the taps. Incorrect coupling of gas cylinder. Check that the coupling is sound. Possible gas leak. Shut off the gas supply, ventilate the premises and immediately notify an authorised installation technician to check and certify the installation. Do not use the appliance until ensuring that there is no gas leak in the installation or appliance itself. A burner switches off and a The safety system has been activated, cutting off Turn the burner control knob to the off position. beep sounds. the gas supply. The beep will stop. You can now use your hob normally. Fault Possible cause Solution All the burners switch off Hob overheating. Turn all the control knobs to the off position. The and a beep sounds. beep will stop. Wait 30 min before using the hob again. If the beep continues, call the Technical Assistance Service. All the burners switch off General fault detected. A whistling noise will be made after one minute. If and a beep sounds. not, call the Technical Assistance Service. Technical Assistance Service When contacting our Technical Assistance Service, please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the specifications plate located on the lower section of the hob and on the label in the user manual. Please find the contact data of all countries in the enclosed customer service list. To book an engineer visit and product advice GB 0844 8928979 Calls from a BT landline will be charged at up to 3 pence per minute. A ca...
Este manual também é adequado para os modelos :Hobs - NPD615XNL/15 (1.66 mb)