Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Discard shrouds. 4. Install new side shrouds in reverse order. Torque the shroud screws 12-15 in lbs. 5. Torque crank arm screws 15-20 ft lbs. „ Crank Arm RT w/Screws Crank Arm LT w/Screws End Cap i) w/Screws 2 Lifecycle LC95R, LC91R, LC85R, R9, and R7 Recumbent Exercise Bikes How To... Remove the Drive Belt Special Service Tools: NONE Note: An access hole in the crank pulley allows removal or loosening of the idler bracket bolt with a socket. 1. Remove the right side shroud. See "How To..." in this section. 2. Rotate the crank pulley until the idler bracket mounting bolt is visible through the access hole in the crank pulley, then loosen the bolt. 3. Loosen the belt tension by loosening the adjusting bolt on the idler bracket. 4. Remove old belt and discard. 5. Install new belt in reverse order. Access Hole. Drive Belt Bracket Adjusting Bolt 6. Adjust belt tension 100-110 lbs by moving the idler bracket down. Insert a straight blade screwdriver in the slotted lip of the bracket to obtain specified tension. When belt tension is achieved, then tighten the mounting bolt and adjustable bracket bolt. Remove the right shroud. See "How To..." in this section. 3 Lifecycle LC95R, LC91R, LC85R, R9, and R7 Recumbent Exercise Bikes How To... Replace the Alternator Belt Special Service Tools: NONE 3. Remove the side shrouds. See “How To...” in this section. Index the location of the tensioning bolt to the alternator mounting bracket, and then loosen the tensioning bolt. Loosen the pivot bolt, and then rotate the alternator until the belt can be removed from the alternator pulley and the intermediate pulley. Install new alternator belt in reverse order. Position the alternator belt on the far left groove of the alternator flywheel pulley (towards user side) and in the center of the alternator pulley (large pulley). Then tighten the belt back to the index mark or 70-80 lbs. Alternator Belt Alternator Belt 4 Lifecycle LC95R, LC91R, LC85R, R9, and R7 Recumbent Exercise Bikes How To... Replace the Crank Shaft Hub Assembly Special Service Tools: Bearing Service Tool Kit - Part Number: BearingToolKit Note: The left shroud does not require removal to service the left crank shaft hub. 1. Remove the right crank arm and shroud. See “How To...” in this section. 2. Remove the drive belt. See “How To...” in this section. 3. Remove the bolt and washer in the center of the hub. NOTE: There is an arrow mark on each hub which is located 180 degrees apart, and is used for proper crank arm position. 4. Install the disc puller plate as illustrated on the left hub. Hub Arrow Mark Drive Belt 5. Turn the puller forcing bolt clockwise until the let hub is removed. Discard the hub. NOTE: The right hub is removed with the crank shaft pulley attached. Use the puller as described in left hub removal. Once off, remove the three screws at the back of the pulley to separate it from the hub. NOTE: Make sure the arrow mark on the hub is pointing 180 degrees from the other hub. 6. Position the new hub on the crank shaft with the washer. Install the mounting bolts and tighten evenly until the hub is fully seated on the shaft. Torque: 220-240 in lbs. NOTE: If the right hub was replaced, then install the hub back on the pulley first and secure using the three mounting screws. 7. Reinstall the side shrouds, crank arms, and pedals. Forcing Boit (1/2-13) Mounting Bolt(3) (1/4-20) 5 Lifecycle LC95R, LC91R, LC85R, R9, and R7 Recumbent Exercise Bikes How To... Replace the Crank Shaft Bearings Special Service Tools: Bearing Service Tool Kit - Part Number: BearingToolKit Snap Ring (large) N Thrust Washer (large) Thrust' Bearing 1. Remove the side shrouds. See “How To...” in this section. 2. Remove the main drive belt. See “HowTo ... “in this section. 3. Remove the crank shaft hubs. See “HowTo...” in this section. 4. Remove the large snap rings, the bowed snap rings, the large and small thrust washers, and the thrust bearings from both sides of the crank shaft. 5. Push the crank shaft out from the frame bearings. 6. Inspect, and if necessary, replace any crank shaft component parts before reassembling onto the new crank shaft. 7. Install the bearing puller on the crank frame bearings as illustrated. Snap Ring Bowed (small) Frame Bearings(2) / Crank Thrust Washer (small) Frame Thrust Washer (large) Snap Ring Bowed (small) Threaded Rod Thrust Washer (small) Thrust Bearing Snap Ring large) Hex Nut- Bike Frame hrust Washer Spacer Frame Bearings Hub INSTALLING CRANK BEARING KIT 6 Lifecycle LC95R, LC91R, LC85R, R9, and R7 Recumbent Exercise Bikes How To... Replace the Crank Shaft Bearings - Continued Special Service Tools: Bearing Service Tool Kit - Part Number: BearingToolKit 8. Press out the frame bearings by rotating the hex nut clockwise until the bearings drop into the puller hub. Once the bearings are out of the frame, disassemble the puller assembly, and dis...
Este manual também é adequado para os modelos :Bicicletas - LC8500R (8.67 mb)