Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Rubber grommet Upright support 17 16 Lower support Base tube 18 20 19 Read CAUTION above Step 18. End cap End cap Coaxial/power cable Preparing the EFX556i page 18 Cardio Theater Integrated Bracket Assembly Instructions 21. Replace the back cover Replace the back cover Fit the lip of the back cover into the tabs along the inside surface of the pressure to the top of the back tighten the screws. 22. Reinstall the front cover and secure it two screws removed in step 2. Before tightening the front cover be sure to fit the lip of the front cover into the tabs along the inside surface of the grommet. To complete the installation, refer to the instructions on page 19. Front cover Upright support 21 22 Back cover Upright support Rubber grommet Rubber grommet Front cover Preparing the EFX556i page 19 Bracket cover Bracket assembly Bracket cover Coaxial/power cable with three connectors Bracket cover Bracket assembly Bracket cover Coaxial/power cable with three connectors Cardio Theater Integrated Bracket Assembly Instructions 4Install the Bracket Assembly 1. Remove the bracket cover. Loosen the bolts on the pivot tube using a ....-inch hex key. Pull the bracket cover away from the assembly. Set it aside. 2. Feed the coaxial/power cable with its three connectors through the bracket assembly. Ask your assistant to hold the bracket assembly near the upright support while you slide the coaxial/power cable and its three connectors (coaxial, power, and DVD) through the bracket assembly tube. 1 2 Install the Bracket Assembly page 20 Cardio Theater Integrated Bracket Assembly Instructions 3. Fit the bracket assembly console bracket. Ask your assistant to lift the and position it along the back console bracket. Make sure the slides into place so that the cutouts base of the flanges fit around the bottom screws. 4. Secure the bracket assembly to the display console bracket. Ask your assistant to continue holding the bracket assembly, while you align the mounting holes and replace the remaining two display console bracket screws. Securely tighten all four screws using a ....-inch hex key. 3 EFX556i 4 EFX546iEFX556i Bracket assembly Bracket assembly Bracket flange Bottom screw Upright support Bracket assembly Install the Bracket Assembly page 21 Cardio Theater Integrated Bracket Assembly Instructions 5Attach the LCD Screen Important: The screen spacer is used only for the Cardio Theater PVS4/5/15 LCD Screen. 1. To protect the LCD Screen for the next few steps, place it screen side down on a clean work surface. Important: Use proper materials to protect the LCD Screen while you remove the plastic cover and metal mounting bracket from the backside of the LCD Screen. 2. Remove the plastic cover. Use a Phillips-head screwdriver to remove the two screws holding the plastic cover to the LCD Screen. Discard the plastic cover and the screws. 3. Remove the metal mounting bracket. Remove the four screws securing the metal mounting bracket. Discard the mounting bracket and the four screws. 4. Retrieve four new Phillips-head screws from the bracket assembly package. Note: Use the longer screws if attaching the screen spacer with the PVS4/5/15 LCD Screen. 5. Attach the LCD Screen to the bracket assembly. If you have the Cardio Theater PVS4/5/15 LCD Screen, you will need to insert the screen spacer between the screen and bracket to ensure a proper fit. 2 Plastic cover 3 Metal mounting bracket LCD screen LCD screen Bracket assembly5 Note: The screen spacer rests between the bracket assembly and the PVS4/5/ 15 LCD Screen. Screen spacer (PVS4/5/15 LCD Screen only) Attach the LCD Screen page 22 Cardio Theater Integrated Bracket Assembly Instructions 6. Fully tighten the bottom Use a Phillips-head screwdriver the bottom two screws. Leave screws finger tight. 7. Connect the coaxial/power cable the LCD Screen. Attach the connectors—coaxial, power, and DVD—to the back of the LCD Screen. Note: If you do not have a DVD option, you can feed the DVD cable back into the pivot tube compartment so it is not hanging out. 8. Connect the controller cable. Feed the controller cable through the front side of the pivot tube and attach it to the back of the LCD Screen. You will hear a definite click as the connector snaps into place inside its receptacle. Note: For more information about cable connections, refer to the Cardio Theater LCD Screen manual. Important: If you purchased the DVD Integrated Bracket Option, you will want to install that option before you continue to the next section. Refer to the DVD Integrated Bracket Option Guide for assembly instructions. 6 7 Coaxial connector Power connector DVD connector Note: If you do not have the DVD option, you can feed the DVD cable back into the pivot tube compartment so it is not hanging out. 8 Controller cable Attach the LCD Screen page 23 Cardio Theater Integrated Bracket Assembly Instructions Reinstall the 6 Bracket Cover 1. Prepare the fasteners for reinstalling the cover. Push the washers and bearings tow...