Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Toggle between the specified wheel size (tire circumference) and . Use this function if the computer is to be shared between two bicycles. Pressing MODE toggles between and . Wheel size entry ...... Pressing MODE increases the value, and pressing and holding MODE moves to the next digit. **To enter the wheel size , display using “Wheel selection”. Sensor ID setting ...... Pressing MODE changes to ID1 or ID2, and pressing and holding MODE moves to Standby. To set the ID, refer to “Preparing the computer-4.” **ID2 is used when the computer is shared with the second sensor. The computer identifies ID1 and ID2 automatically. Clock setting ............. To set the clock, refer to “Preparing the computer-5”. Total distance manual entry ................................. Before reinitializing the computer, note the total distance. This reading will later allow you to enter the total distance manually. Speed unit ................ Pressing MODE toggles between km/h and mph. Maintenance To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and wipe it off with a dry cloth. Replacing the battery Computer Replace the battery when the digit of the selected Mode flashes. Install a new lithium battery (CR2032) with the (+) side facing upward. Then reinitialize the computer referring to “Preparing the computer”. **When the battery is installed, place the seal with the “TOP” side upward. Sensor Replace the battery when the Speed digit flashes. After replacement, check the positions of the sensor and magnet. **After the battery is replaced, ID setting is required again. For details, refer to “Sensor ID setting” on the menu screen. TOP TOP COIN Starting/Stopping measurement Measurements start automatically when the bicycle is in use. During measurement, km/h or mph flashes. Switching computer function Pressing MODE switches function, in order, as shown on the left. Resetting data To reset measurement data, display any data other than for Dst-2 and then press and hold MODE. Pressing and holding MODE with Dst-2 displayed resets Dst-2 only. The total distance is never reset. Power-saving function If the computer has not received a signal for 10 minutes, power-saving mode will activate and only the clock will be displayed. When the computer receives a sensor signal again, the measuring screen reappears. If 60 minutes’ inactivity elapses, power-saving mode will change to SLEEP mode. Pressing the MODE in SLEEP mode brings up the measuring screen. Changing the computer settings [menu screen] If the MENU is pressed with the measuring screen displayed, the menu screen appears. Press the MODE when measurement has stopped and no signal is being received to change menu settings. Operating the computer [Measuring screen] Wheel selection Wheel size entry Sensor ID setting Clock setting Total distance manual entry Speed unit CR2032 Push! Seal CR2032 Pace arrow Indicates whether the current speed is faster ( ) or slower ( ) than the average speed. Current speed 0.0(4.0) - 105.9 km /h [0.0(3.0) - 65.9 mph] Selected Mode ***With the computer installed on the bracket, press on the three raised dots on the face of the computer. *** If Tm exceeds approximately 27 hours or Dst exceeds 999.99 km, .E (Error) is displayed as the average speed. Reset data. Tm Elapsed Time 0:00’00” - 9:59’59” Dst Trip Distance 0.00 - 999.99 km [mile] C Cadence 0(20) - 299 rpm Dst2 Trip Distance-2 0.00 - 999.99 / 1000.0 - 9999.9 km [mile] Av Average Speed*2 0.0 - 105.9 km/h [0.0 - 65.9 mph] Mx Maximum Speed 0.0(4.0) - 105.9 km/h [0.0(3.0) - 65.9 mph] Odo Total Distance 0.0 - 9999.9 / 10000 - 99999 km [mile] Clock 0:00 - 23:59 or 1:00 - 12:59 MODE Setting change (by pressing & holding) **After changing, be sure to press MENU to register the setting. **If the menu screen is not touched for a minute, the Measuring screen reappears without data changes. Troubleshooting MODE does not work when the computer is mounted on its bracket. Check that there is no dirt between the bracket and the computer. Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly. The Sensor signal reception icon does not flash (the speed or cadence is not displayed). Move the computer near the sensor, and turn the rear wheel or crank. If the Sensor signal reception icon flashes, this trouble may be due to battery drain, not any malfunction. Set the sensor ID. Set the ID according to “Sensor ID setting” on the menu screen. Check that the clearance between each sensor and magnet is not too large. (Clearance: less than 5 mm for Speed, and 3 mm for Cadence) Check that the magnet goes through the relevant sensor zone. Adjust the positions of the magnet and sensor. Check that the distance between the computer and sensor is correct (Distance: within 20 to 100 cm) Install the sensor within the specified range. Is the computer or sensor battery weak? In winter, battery performance diminishes. Replace with new batteries. Af...
Este manual também é adequado para os modelos :Bicicletas - CYCLOCOMPUTER CC-RD400DW (1.77 mb)