Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• Be sure to securely mount the magnet, the sensor, and the bracket on your bicycle. Periodically check to insure they are mounted securely and the screws are not loosen. • Keep batteries out of reach of small children. Dispose of batteries according to local regulations. • Avoid unnecessary prolonged exposure to the sun. Never attempt to disassemble the computer head. • Don’t use thinner, benzene or alcohol to wipe the surface of the computer. They may damage the surface of computer. Computer Set-up (For 1st use or after replacing the battery) All Clear Push three buttons (MODE, START/ STOP and SET) at the same time. * Do this procedure without fail for stable measurement when you use this system for the first time and every time the battery is replaced. 1 Starting the odometer from zero. Retaining the current odometer reading (the odometer starts from the reading you inputted) SET MODE MODE ST/STOP ST/STOP Set The Tire Circumference Set the tire circumference in cm. Note You can easily set it by referring to the chart shown right. Setting is completed by pushing the SET button. 3 Increase the number. Max. 300 cm Decrease the number Min. 100 cm Preparation Complete. (the screen will show the time measurement in this state) * The auto mode is ON in this state. MODE Button START/STOP Button SET Button ! L(cm) 14 x 1.50 102 14 x 1.75 106 16 x 1.50 119 16 x 1.75 120 18 x 1.50 134 18 x 1.75 135 20 x 1.75 152 20 x 1-3/8 162 22 x 1-3/8 177 22 x 1-1/2 179 24 x 1 175 24 x 3/4Tubular 178 24 x 1-1/8 179 24 x 1-1/4 191 24 x 1.75 189 24 x 2.00 192 24 x 2.125 196 26 x 7/8 192 26 x 1(59) 191 26 x 1(65) 195 26 x 1.25 195 26 x 1-1/8 190 26 x 1-3/8 207 26 x 1-1/2 210 26 x 1.40 200 26 x 1.50 201 26 x 1.75 202 26 x 1.95 205 26 x 2.00 206 26 x 2.10 207 26 x 2.125 207 26 x 2.35 208 26 x 3.00 217 27 x 1 215 27 x 1-1/8 216 27 x 1-1/4 216 27 x 1-3/8 217 650 x 35A 209 650 x 38A 212 650 x 38B 211 700 x 18C 207 700 x 19C 208 700 x 20C 209 700 x 23C 210 700 x 25C 211 700 x 28C 214 700 x 30C 217 700 x 32C 216 700C Tubular 213 700 x 35C 217 700 x 38C 218 700 x 40C 220 L cm SET ST/STOP MODE Contact Point Select The Measurement Unit Select the measurement unit, kilometer or mile, by pushing the MODE button. 2 MODE Choose Either of The Followings. • When you want to input the reading of the currently used odometer, keep pressing the MODE button for two seconds and input the reading. • When you want to start the odometer from zero, push the START/STOP button. Kilometer Mile SET Button MODE Button START/STOP Button Input the current reading of odometer. For two seconds. Increase the number. Move the decimal point. You need to know the tire circumference (L cm) beforehand. Tire size Tire size is usually shown on the sidewall of tires. ® U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending Copyright © 2002 CAT EYE Co. Ltd. CCMED3-021210 066600240 1 5 3 3 7 3 5 5 OK 1 2 4 3 5 6 7 8 3 2 1 8 7 ENDURO8 8 1 7 1 6 Installation of the Computer on Your Bike The computer is combined with the following parts. Mount The Bracket Secure the cord on the fork with the nylon ties 7 and lead to the handle bar along the outer cable of the bicycle by means of the spiral tube 8. Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the screw. Slide the computer into the bracket 1 until you hear the click sound. The contact points are automatically closed. When you need to detach the computer, slide forward the computer with the lever pushed simultaneously. Note Allow enough wire clearance in the area marked with an to insure that you can turn the handlebar from left to right without pulling the wire. Test The Basic Functions Rotate the front wheel gently and see if the computer indicates the running speed. Note When the computer does not indicate the speed, check the position of the magnet and the sensor. 4 1 Bracket 2 Cord 3 Sensor 4 Sensor Rubber Pad Center 5 Magnet 6 Bracket Rubber Pad 7 Five Nylon Ties 8 Spiral Tube Front Fork 3 2 1 Please read these instructions carefully before attempting to install and use your CAT EYE ENDURO 8 computer so that you understand the functions of this product. Please don’t throw away this manual, Keep the manual at a place easily accessible. CAT EYE ENDURO 8 CYCLOCOMPUTER CC-ED300 E: Owner’s Manual Spoke Rotate the front wheel. Front Fork Sensor Side Within 5 mm Marked Line Mount sensor and adjust the gap between the magnet and the sensor. Secure the sensor 3 with the larger nylon ties 7 at the appropriate place and in the right direction. Mount the magnet 5 on a spoke of the front wheel so that the surface of the magnet will face the sensor. Lever Important Note Mount the sensor 3 at the appropriate position so that the center of the magnet 5 will align with the marked line on the sensor when the wheel is rotated. Important Note Rotate the sensor on the front fork to adjust the gap between the sensor and the magnet 5 within 5 mm, and secure it with the nylon ties. 1 You can ...